Numerical Analysis to Determine the Distribution of Tool Forces and Temperatures of Single Point Cutting Tool
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Call for Papers | Fully Refereed | Open Access | Double Blind Peer Reviewed

ISSN: 2319-7064


Downloads: 128 | Views: 309 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

M.Tech / M.E / PhD Thesis | Mechanical Engineering | India | Volume 3 Issue 4, April 2014 | Popularity: 7.1 / 10


     

Numerical Analysis to Determine the Distribution of Tool Forces and Temperatures of Single Point Cutting Tool

Maheshwari N Patil, Shreepad Sarange


Abstract: This paper presents a methodology to determine tool forces, distribution of temperatures to estimate distribution of stresses and deformation on the single point cutting tool in the process of metal cutting. In mechanism of metal cutting a cutting tool exerts a compressive force on the work piece. Under this compressive force the material of the work piece is stressed beyond its yield point causing the material to deform plastically and shear off. The sheared material begins to flow along the cutting tool face in the form of small pieces called chips. The flowing chips causes the wear of cutting tool. Heat is produced during shearing action the heat generated raises the temperature of tool, work and chips. The temperature rise in cutting tool tends to soften it and causes loss of keenness in the cutting edge leading to its failure. This temperature during metal cutting is to be maximum at the tip of the tool, is too measured by experimental set up and which are required as input to the software and analyzes the stresses and deformation on the single point cutting tool. Now manufacturing industries are mostly concentrating on a cost reduction. When it is not possible to reduce the fixed cost, it is necessary to concentrate on variable cost like electricity, cutting fluids, cotton waste, oil grease, welding rods, cutting tools etc.


Keywords: forces, temperatures, yield point, deform plastically, wear, analyses, stresses, deformation, variable cost


Edition: Volume 3 Issue 4, April 2014


Pages: 765 - 771



Make Sure to Disable the Pop-Up Blocker of Web Browser


Text copied to Clipboard!
Maheshwari N Patil, Shreepad Sarange, "Numerical Analysis to Determine the Distribution of Tool Forces and Temperatures of Single Point Cutting Tool", International Journal of Science and Research (IJSR), Volume 3 Issue 4, April 2014, pp. 765-771, https://www.ijsr.net/getabstract.php?paperid=20131565, DOI: https://www.doi.org/10.21275/20131565

Similar Articles

Downloads: 0

Research Paper, Mechanical Engineering, India, Volume 11 Issue 8, August 2022

Pages: 556 - 559

Effect of Pre Oxidation on Microstructure and Hardness of Low Carbon Steel during Nitrocarburising

Dr. Nirmala L.

Share this Article

Downloads: 1 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, China, Volume 13 Issue 4, April 2024

Pages: 1173 - 1180

An Elastoplastic Model Simulation to Investigate the Bending Load on Lattice Structures

Reza Shamim

Share this Article

Downloads: 2

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 698 - 702

FEA of Double Shear Lug Joint by Varying Material Combinations

B. Vijaya Kumar, F. Anand Raju

Share this Article

Downloads: 2 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Analysis Study Research Paper, Mechanical Engineering, India, Volume 12 Issue 6, June 2023

Pages: 1198 - 1203

Theoretical Analysis and Thermal Design of Solar Cooking Unit with NaNO3+KNO3 Phase Change Material

Dr. Krishna Shrivastava

Share this Article

Downloads: 2 | Weekly Hits: ⮙2 | Monthly Hits: ⮙2

Masters Thesis, Mechanical Engineering, India, Volume 12 Issue 9, September 2023

Pages: 533 - 541

Analysis and Design Optimization of Hallow Section Valve Springs

Jagadish R. Bagali, R. S. Matti, B. S. Vivekanand

Share this Article
Top