Cutting Parameters Effects on Surface Roughness During End Milling of Aluminium 6061 Alloy Under Dry Machining Operation
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Call for Papers | Fully Refereed | Open Access | Double Blind Peer Reviewed

ISSN: 2319-7064


Downloads: 122 | Views: 335

Research Paper | Mechanical Engineering | Nigeria | Volume 4 Issue 7, July 2015 | Popularity: 6.8 / 10


     

Cutting Parameters Effects on Surface Roughness During End Milling of Aluminium 6061 Alloy Under Dry Machining Operation

Okokpujie Imhade. P, Okonkwo Ugochukwu.C, Okwudibe Chinenye. D.


Abstract: In this project an experimental investigation of the cutting parameters effects on surface roughness during end milling of aluminium 6061 under dry machining operation was carried out. The experiments were carried out to investigate surface quality of the four machined parameters and to developed mathematical models using least square approximation techniques. Spindle speed (N), axial depth of cut (a) radial depth of cut (r) and feed rate (f), has been chosen as input variables in order to predict surface roughness. The experiment was designed by using central composite design (CCD) in which 30 samples were run in a CNC milling machine. Each of the experimental result was measured using Press-o-firm and Mitutoyo surface tester. After the predicted surface roughness values have been obtained the average percentage errors were calculated. The mathematical model developed by using least square approximation method shows accuracy of 91 % which is reasonably reliable for surface roughness prediction. With the obtained optimum input parameters for surface roughness, production operations will be enhanced.


Keywords: CNC end milling, Surface roughness, Response surface methodology


Edition: Volume 4 Issue 7, July 2015


Pages: 2030 - 2036



Make Sure to Disable the Pop-Up Blocker of Web Browser


Text copied to Clipboard!
Okokpujie Imhade. P, Okonkwo Ugochukwu.C, Okwudibe Chinenye. D., "Cutting Parameters Effects on Surface Roughness During End Milling of Aluminium 6061 Alloy Under Dry Machining Operation", International Journal of Science and Research (IJSR), Volume 4 Issue 7, July 2015, pp. 2030-2036, https://www.ijsr.net/getabstract.php?paperid=SUB156886, DOI: https://www.doi.org/10.21275/SUB156886

Similar Articles

Downloads: 2 | Weekly Hits: ⮙2 | Monthly Hits: ⮙2

Experimental Result Paper, Mechanical Engineering, India, Volume 13 Issue 12, December 2024

Pages: 1577 - 1582

An Experimental Study on Wear Strength of Aluminium 7075 Reinforced with Magnesium and Boron Carbide

Raviprakash T N, Sreedharamurthy T, Thimmegowda M B

Share this Article

Downloads: 3

Masters Thesis, Mechanical Engineering, Indonesia, Volume 10 Issue 12, December 2021

Pages: 590 - 595

Study of the Finite Plain Journal Bearing Considering Cavitation and Roughness Effect

Ganjar Kurnia, Mohammad Tauviqirrahman, Ojo Kurdi, Budi Setyana

Share this Article

Downloads: 3 | Weekly Hits: ⮙2 | Monthly Hits: ⮙2

Research Paper, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2846 - 2847

Experimental Investigation of Different Material Surface Morphology on Formation of Transfer Layer

M. Basavaraju, Maharudra

Share this Article

Downloads: 3 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 4 Issue 2, February 2015

Pages: 2482 - 2486

Impact of Hard Material Surface Morphology on Friction and Transfer Layer Formation

M. Basavaraju, Shivakumar N V

Share this Article

Downloads: 3 | Weekly Hits: ⮙3 | Monthly Hits: ⮙3

Research Paper, Mechanical Engineering, Turkiye, Volume 13 Issue 8, August 2024

Pages: 1123 - 1125

Analysis of Cutting Parameters Impact on Forces during AISI 304 Stainless Steel Turning

Bugra Akin, Ali Serhat Ersoyoglu

Share this Article
Top