International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Call for Papers | Fully Refereed | Open Access | Double Blind Peer Reviewed

ISSN: 2319-7064


Downloads: 132 | Views: 318 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Review Papers | Mechanical Engineering | India | Volume 4 Issue 6, June 2015 | Popularity: 6.6 / 10


     

A Review on Optimizing Process Parameters for TIG Welding using Taguchi Method & Grey Relational Analysis

Imran A. Shaikh, M. Veerabhadra Rao


Abstract: Gas tungsten arc welding (GTAW) or Tungsten inert gas welding (TIG) is one of the widely used techniques for joining ferrous and non-ferrous metal. Gas tungsten arc welding process, consist of non-consumable tungsten electrode which is used to provide the arc for welding. During the welding cycle a shield of inert gas expels the air from the welding area and prevents oxidation of the electrode, weld puddle and surrounding heat-affected zone. For joints where additionally weld metal is needed, a filler rod is fed into the puddle. In the present review paper an attempt is made to understand the effect of TIG welding parameter, that are influences on responsive output parameters such as tensile strength of welding, distortion due to welding by using optimization method. Welding parameters such as welding current, gas flow rate, root gap, bevel angle are main parameter which is mostly used.


Keywords: TIG welding, Process Parameters optimization, Taguchi method, Grey Relational Analysis


Edition: Volume 4 Issue 6, June 2015


Pages: 2449 - 2452



Make Sure to Disable the Pop-Up Blocker of Web Browser




Text copied to Clipboard!
Imran A. Shaikh, M. Veerabhadra Rao, "A Review on Optimizing Process Parameters for TIG Welding using Taguchi Method & Grey Relational Analysis", International Journal of Science and Research (IJSR), Volume 4 Issue 6, June 2015, pp. 2449-2452, https://www.ijsr.net/getabstract.php?paperid=SUB155855

Similar Articles

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Downloads: 116

Research Paper, Mechanical Engineering, India, Volume 6 Issue 11, November 2017

Pages: 1833 - 1842

An Experimental Investigation and Optimization of Electrical Discharge Drilling for Small Hole Drilling with High Aspect Ratio

Ashok Kumar, Sandeep Kumar Rawal

Share this Article

Downloads: 117

Research Paper, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 2699 - 2702

Optimization of End Milling Parameters on Surface Roughness of Die Steel HCHCr by Taguchi Method

M. S. Harne, Ravikumar L. Shirsat

Share this Article

Downloads: 119 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this Article

Downloads: 122 | Weekly Hits: ⮙4 | Monthly Hits: ⮙4

Research Paper, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 1099 - 1103

Parametric Optimization of Metal Inert Gas Welding and Tungsten Inert Gas Welding By Using Analysis of Variance and Grey Relational Analysis

Jay Joshi, Manthan Thakkar, Sahil Vora

Share this Article
Top