International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064




Downloads: 117

Research Paper | Mechanical Engineering | India | Volume 4 Issue 1, January 2015


Optimization of End Milling Parameters on Surface Roughness of Die Steel HCHCr by Taguchi Method

M. S. Harne, Ravikumar L. Shirsat


Abstract: - This paper outlines the Taguchi Optimization methodology, which is applied to optimize cutting parameters in end milling when machining Die steel (HCHCr D3). The milling parameters evaluated are cutting speed, feed rate and Depth of cut. An orthogonal Array, signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are employed to analyze the effect of experiment (DOE), Mathematical model is generated by regression analysis. . Finally effect of process parameter on surface roughness (Ra) in end milling studied and optimum solution is carried out. The study shows that the taguchi method is suitable to solve the surface quality problem with minimum number of trials.


Keywords: Optimisation, End Milling, Taguchi Method, Surface Roughness, orthogonal Array, ANOVA


Edition: Volume 4 Issue 1, January 2015,


Pages: 2699 - 2702


How to Cite this Article?

M. S. Harne, Ravikumar L. Shirsat, "Optimization of End Milling Parameters on Surface Roughness of Die Steel HCHCr by Taguchi Method", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=SUB15954, Volume 4 Issue 1, January 2015, 2699 - 2702

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'Optimisation'

Downloads: 111

Research Paper, Mechanical Engineering, India, Volume 4 Issue 10, October 2015

Pages: 1995 - 1997

Design and Optimisation of an FSAE Restrictor with Structured Mesh

Vilas D Ravindra, Pavan Kumar AV, Abhilash PK, Nikhil M, Yeshodhara B

Share this Article

Downloads: 121

Research Paper, Mechanical Engineering, India, Volume 3 Issue 7, July 2014

Pages: 1234 - 1238

Aerothermodynamic Design and Optimisation of Hypersonic Research Reentry Vehicle

Manjunatha H, C. N. Nataraj

Share this Article

Similar Articles with Keyword 'Taguchi Method'

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Downloads: 116

Research Paper, Mechanical Engineering, India, Volume 6 Issue 11, November 2017

Pages: 1833 - 1842

An Experimental Investigation and Optimization of Electrical Discharge Drilling for Small Hole Drilling with High Aspect Ratio

Ashok Kumar, Sandeep Kumar Rawal

Share this Article

Similar Articles with Keyword 'Surface Roughness'

Downloads: 100

Research Paper, Mechanical Engineering, India, Volume 6 Issue 9, September 2017

Pages: 913 - 916

Pulsed Laser Micro Polishing of Metals Using Dual-Beam Technology

Lagad Rahul Anil, Dr. Ashwini Kumar

Share this Article

Downloads: 101

Research Paper, Mechanical Engineering, Saudi Arabia, Volume 5 Issue 5, May 2016

Pages: 1447 - 1454

Tactile Perception of Passenger Vehicle Interior Polymer Surfaces: An Investigation using Fingertip Blind Observations and Friction Properties

Mohammad S. Alsoufi

Share this Article

Similar Articles with Keyword 'orthogonal Array'

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Downloads: 117

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this Article

Similar Articles with Keyword 'ANOVA'

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Downloads: 117

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this Article
Top