Research Paper | Mechanical Engineering | India | Volume 4 Issue 6, June 2015
Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis
D.U.M. Manikanta, A. Chennakesava Reddy
In this paper 3D finite element analysis and Taguchi technique were employed to investigate fracture criteria of 6061 Al-alloy pipes subjected to internal bursting pressure. The ultimate tensile strength and yield strength criteria were used to study the failure of pipes. It was observed that the J-integral was proportional to the deformation under the applied bursting pressure. It was noticed that the major dominating control factors which could influence the failure of pipes were the pipe thickness, depth of crack and the bursting pressure.
Keywords: AA6061, bursting pressure, fracture criteria, crack depth, crack length, J-integral, stress intensity factor, Taguchi technique
Edition: Volume 4 Issue 6, June 2015
Pages: 1509 - 1515
How to Cite this Article?
D.U.M. Manikanta, A. Chennakesava Reddy, "Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=SUB155636, Volume 4 Issue 6, June 2015, 1509 - 1515
108 PDF Views | 76 PDF Downloads
Similar Articles with Keyword 'AA6061'
Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015
Pages: 1509 - 1515Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis
D.U.M. Manikanta, A. Chennakesava Reddy
Research Paper, Mechanical Engineering, India, Volume 5 Issue 9, September 2016
Pages: 1755 - 1760Experimental Investigation the Effect of Weld Parameters on Mechanical and Metallurgical Properties of Dissimilar Joints AA6082?AA6061 in T6 Condition Produced by FSW
Vipul Chaudhari, Manish Rahevar
Research Paper, Mechanical Engineering, Iraq, Volume 8 Issue 1, January 2019
Pages: 267 - 271A Study of New Parameters Effect on the Springback of Aluminum Sheets in Plane Strain Bending
Fathi Al-shamma, Hajer M. Issmael
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 9 Issue 1, January 2020
Pages: 58 - 64Fabrication and Estimation of Mechanical Properties of Aa6061 Matrix Reinforced with Al2O3 and Stainless Steel 316 Powder
Bheem Rao .P, Prasanna .P
Similar Articles with Keyword 'crack depth'
Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015
Pages: 1509 - 1515Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis
D.U.M. Manikanta, A. Chennakesava Reddy
Research Paper, Mechanical Engineering, India, Volume 8 Issue 4, April 2019
Pages: 1572 - 1575Damage Detection in Single Tapered Rectangular Cross Section Cantilever Beam using Neural Networks based on Vibration Characteristics
Dr. Challa Jayaramulu
Research Paper, Mechanical Engineering, India, Volume 8 Issue 5, May 2019
Pages: 1288 - 1293Vibration-Based Methods for Detecting a Crack in a Fixed Free Beam
Dr. Challa Jayaramulu
Similar Articles with Keyword 'stress intensity factor'
Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015
Pages: 1509 - 1515Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis
D.U.M. Manikanta, A. Chennakesava Reddy
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 8, August 2016
Pages: 1539 - 1543Analysis of Cracks Starting from a Square Hole in a Rectangular Plate
S. M. Rajmane, Shailesh Birajdar
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 9, September 2014
Pages: 426 - 431Characterization, AC Conductivity and Dielectric behaviour of Chemically Synthesized Poly Meta-Aminophenol
Dr. Shantharaja M., Srinivas K. R.
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 4, April 2014
Pages: 316 - 318Optimization of Stress Intensity Factor for Natural Rubber Toughened Glass Fiber
Nikhil S, D G Harris Samuel
Similar Articles with Keyword 'Taguchi technique'
Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015
Pages: 1509 - 1515Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis
D.U.M. Manikanta, A. Chennakesava Reddy
Review Papers, Mechanical Engineering, India, Volume 4 Issue 3, March 2015
Pages: 2364 - 2368Review of Optimization Aspects for Casting Processes
Yazad N. Doctor, Dr. Bhushan T. Patil, Aditya M. Darekar
Research Paper, Mechanical Engineering, India, Volume 2 Issue 6, June 2013
Pages: 462 - 465Tribological Characterisation and Morphological Study of Epoxy Composites filled with WS2 under Dry Sliding
M. H. Shaikh, G. J. Pawar, J. S. Sidhu
Review Papers, Mechanical Engineering, India, Volume 8 Issue 3, March 2019
Pages: 1782 - 1784A Review on the Parametric Optimization in MIG Welding using Taguchi Method
Mandeep Singh, Dr. Balbir Singh
Research Paper, Mechanical Engineering, India, Volume 6 Issue 1, January 2017
Pages: 334 - 339Parametric Optimization for Friction Stir Welding of Al6061 Alloy using Taguchi Technique
Lingam Satyavinod, R Harikishore