Modal and Thermal Analysis of Gas Turbine Multi Stage Rotor
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

M.Tech / M.E / PhD Thesis | Mechanical Engineering | India | Volume 4 Issue 5, May 2015

Modal and Thermal Analysis of Gas Turbine Multi Stage Rotor

Ganipineni Sai Krishna, Venkata Ramana Nynala

Gas turbines are essential in generation of power in the field of aviation etc., proper design of all the elements of the gas turbine will play a pivotal role in providing an efficient and ergonomic gas turbine. Gas turbine rotor is one of the key elements of gas turbine.Hence analysis of gas turbine rotor is essential. Gas turbine rotor assembly is mainly subjected to centrifugal stresses with high temperature gradients. If these stresses are beyond the threshold limit of the strength of the material of the gas turbine rotor, rotor failure will occur. In the present work, the gas turbine rotor assembly is analyzed for thermal loads, centrifugal forces and natural frequency due to the mass of the rotor assembly. The gas turbine rotor will be analyzed as a segment of the design and modeling of gas turbine. In this work structural and thermal characteristics in gas turbine rotor assembly due to various operating conditions will be analyzed by varying the suitable materials, analysis using FEA software ANSYS workbench-14.5 and results are presented. From the results presented, one can say that the structural and thermal characteristics of the rotor will be reduced to eliminate the use of high level materials.

Keywords: gas turbine, Structural, Modal and Thermal Analysis, Finite Element Analysis

Edition: Volume 4 Issue 5, May 2015

Pages: 2985 - 2989

Share this Article

How to Cite this Article?

Ganipineni Sai Krishna, Venkata Ramana Nynala, "Modal and Thermal Analysis of Gas Turbine Multi Stage Rotor", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=SUB155037, Volume 4 Issue 5, May 2015, 2985 - 2989

94 PDF Views | 68 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'gas turbine'

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 761 - 763

Critical Analysis of Fuel Pump Bleed Valve for Typical Jet Engine by Using FMEA Method

Bharath. G, R. Prakash

Share this Article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 4, April 2017

Pages: 2522 - 2526

Investigation on Influence of Cooling Design in Structural Stability of CMSX-4 made Gas Turbine Guide Vanes

Dr. R. Saravanan, G. Vinod Reddy

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 7, July 2014

Pages: 1407 - 1413

Comparative Analysis of Gas Turbine Blades with and without Turbulators

Sagar H T, Kishan Naik

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 5, May 2015

Pages: 2985 - 2989

Modal and Thermal Analysis of Gas Turbine Multi Stage Rotor

Ganipineni Sai Krishna, Venkata Ramana Nynala

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 6, June 2016

Pages: 1103 - 1107

Stress Analysis and Life Estimation of Gas Turbine Blisk for Different Materials of a Jet Engine

Madhu P

Share this Article

Similar Articles with Keyword 'Structural'

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 12, December 2015

Pages: 1359 - 1361

Development and Thermal Characteristics of Maize-Husk Filled Polymer Composite

Shailesh Verma, Anand Shukla

Share this Article

Research Paper, Mechanical Engineering, China, Volume 4 Issue 12, December 2015

Pages: 1988 - 1994

Design and Simulation of Parallel Manipulator for Vehicle Driving Simulator

Khalid Ali Abdelaziz Ali, Liu Ying

Share this Article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 1, January 2017

Pages: 1192 - 1198

Vibrational Analysis of All Terrain Bike [ATB] using FEM

Aishwary Mendke, Suman Sharma

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 2, February 2016

Pages: 1412 - 1415

Modeling and Analysis of a Shaft Blade for its Strength

A. Satya Dinesh, G. V. Naga Mani

Share this Article

Comparative Studies, Mechanical Engineering, India, Volume 3 Issue 7, July 2014

Pages: 324 - 328

Comparison of Methodologies for Conceptual Design of Mechanisms

Shoumik Pravin Kulkarni, Maruti M. Khot

Share this Article

Similar Articles with Keyword 'Finite Element Analysis'

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 3, March 2015

Pages: 1426 - 1430

Modeling and Analysis of Human Liver by Using Finite Element Analysis

N. Kishore Kumar, K. Ashok Kumar Raju

Share this Article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1509 - 1515

Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis

D.U.M. Manikanta, A. Chennakesava Reddy

Share this Article

Research Paper, Mechanical Engineering, China, Volume 4 Issue 5, May 2015

Pages: 1862 - 1866

Laser Shock Forming of Titanium Alloy and Its Simulation Using Abaqus Finite Element Software

David Mbukwa

Share this Article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 2340 - 2344

Finite Element Approach to Stress Analysis for Failure Prediction of a Six DOF Hybrid Kinematic Machine for On-Site Machining

Maxwell Zvikomborero Sakutukwa, Anshul Jain

Share this Article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 2136 - 2140

Investigating the Effects of Different Geometries Used In Flexural Hinges on Their Fatigue Life

Milind Sawant, Prashant Anerao

Share this Article
Top