International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064

Downloads: 106

Research Paper | Production Engineering | India | Volume 4 Issue 5, May 2015

Influence of Process Parameters on Depth of Penetration in GMAW Process by Using Taguchi Method

S. D. Ambekar, Sunil R. Wadhokar

This study is to investigate the influence of process parameters on depth of penetration in Gas metal arc welding (GMAW) process. The optimization for Gas metal arc welding process parameters of Martensitic Stainless steel work piece AISI 410 using Taguchi method is carried out. Sixteen experimental runs (L16) based on an orthogonal array Taguchi method were performed. This paper presents the effect of welding parameters like welding speed, welding current and wire diameter on penetration. The ANOVA and signal to noise ratio (S/N ratio) is applied to identify the most significant factor and predicted optimal parameter setting. Experiment with the optimized parameter setting, which have been obtained from the analysis, are giving valid the results. The confirmation test is conducted and found the results closer to the optimize results. These results showed the successful implementation of methodology.

Keywords: Gas metal arc welding, welding parameters, penetration, signal to noise ratio, orthogonal array

Edition: Volume 4 Issue 5, May 2015

Pages: 3065 - 3069

Share this Article

How to Cite this Article?

S. D. Ambekar, Sunil R. Wadhokar, "Influence of Process Parameters on Depth of Penetration in GMAW Process by Using Taguchi Method", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=SUB155031, Volume 4 Issue 5, May 2015, 3065 - 3069

Enter Your Email Address


Similar Articles with Keyword 'welding parameters'

Downloads: 96

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2721 - 2726

Application of Taguchi Method for Resistance Spot Welding of Stainless Steel-304 Grade

Manjunath R. Rawal, Dr. K. H. Inamdar

Share this Article

Downloads: 99

Review Papers, Production Engineering, India, Volume 4 Issue 4, April 2015

Pages: 3032 - 3034

A Review on Effect of Various Process Parameters on Weld Joint of Dissimilar & Similar Metals in Tig Welding

M. S. Harne, S. S. Sathe

Share this Article

Similar Articles with Keyword 'orthogonal array'

Downloads: 96

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2721 - 2726

Application of Taguchi Method for Resistance Spot Welding of Stainless Steel-304 Grade

Manjunath R. Rawal, Dr. K. H. Inamdar

Share this Article

Downloads: 98

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1331 - 1335

Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process

K. G. Nikam, S. S. Kadam

Share this Article

Similar Articles with Keyword 'Gas'

Downloads: 99

Review Papers, Production Engineering, India, Volume 4 Issue 4, April 2015

Pages: 3032 - 3034

A Review on Effect of Various Process Parameters on Weld Joint of Dissimilar & Similar Metals in Tig Welding

M. S. Harne, S. S. Sathe

Share this Article

Downloads: 110 | Weekly Hits: ⮙3 | Monthly Hits: ⮙8

Research Paper, Production Engineering, India, Volume 7 Issue 4, April 2018

Pages: 903 - 908

Parameter Optimization of CO2 Laser Drilling for Different Features

Siddhant R. Gade, Dr. K. H. Inamdar

Share this Article

Similar Articles with Keyword 'metal'

Downloads: 97

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2153 - 2156

Formability Analysis of Deep drawing Process by Finite Element Simulation

Anup S. Atal, M. T. Shete

Share this Article

Downloads: 99

Review Papers, Production Engineering, India, Volume 4 Issue 4, April 2015

Pages: 3032 - 3034

A Review on Effect of Various Process Parameters on Weld Joint of Dissimilar & Similar Metals in Tig Welding

M. S. Harne, S. S. Sathe

Share this Article

Similar Articles with Keyword 'arc'

Downloads: 93

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1669 - 1671

Milling Fixture for Arcing Contact

Viraj P. Lele

Share this Article

Downloads: 95

Research Paper, Production Engineering, India, Volume 6 Issue 3, March 2017

Pages: 2329 - 2335

Effect and Optimization of Process Parameters using Taguchi Method in WEDM for AISI M42 HSS Material

Joshi Guruprasad R., Dr. A. N. Chapgaon

Share this Article

Similar Articles with Keyword 'welding'

Downloads: 96

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2721 - 2726

Application of Taguchi Method for Resistance Spot Welding of Stainless Steel-304 Grade

Manjunath R. Rawal, Dr. K. H. Inamdar

Share this Article

Downloads: 99

Review Papers, Production Engineering, India, Volume 4 Issue 4, April 2015

Pages: 3032 - 3034

A Review on Effect of Various Process Parameters on Weld Joint of Dissimilar & Similar Metals in Tig Welding

M. S. Harne, S. S. Sathe

Share this Article
Top