International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064




Downloads: 108

Comparative Studies | Manufacturing Engineering | India | Volume 4 Issue 3, March 2015


Experimental Investigation on Surface Roughness in Finish Turning of EN 8 Steel

K. G. Nikam, S. V. Vanjari


Abstract: Good surface quality is the requirement of customers. In the present work it was seen that the desired surface roughness were not obtained consistently in turning of EN 8 steel application (shaft). These higher values of surface roughness results in rework and increases cost hence the main objective is optimization of surface roughness. The surface quality is influenced by cutting speed, feed rate and depth of cut and many other parameters. In the present study attempt has been made to investigate the effect of cutting parameters (cutting speed, feed rate, depth of cut) on surface roughness in the finish turning of EN 8 steel. The CNMG 120412 cutting tool insert was used for experimental work. The experiments have been conducted using Taguchi L9 orthogonal array in a SPEED LX 200 MAJOR CNC lathe machine. Turning process carried out on the EN 8 steel. The optimum cutting condition was determined surface roughness were evaluated by the analysis of variance (ANOVA).


Keywords: Turning, Surface roughness, ANOVA, Taguchi Method, S/N ratio


Edition: Volume 4 Issue 3, March 2015,


Pages: 1291 - 1294


How to Cite this Article?

K. G. Nikam, S. V. Vanjari, "Experimental Investigation on Surface Roughness in Finish Turning of EN 8 Steel", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=SUB152372, Volume 4 Issue 3, March 2015, 1291 - 1294

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'Turning'

Downloads: 107

Review Papers, Manufacturing Engineering, India, Volume 5 Issue 11, November 2016

Pages: 1647 - 1653

Application of CNC Electrical Discharge Turning for Aerospace Materials ? A Review

A. Chennakesava Reddy, Naresh Baki

Share this Article

Downloads: 111

Review Papers, Manufacturing Engineering, India, Volume 6 Issue 5, May 2017

Pages: 2014 - 2017

Review on Optimization Process Parameters of HCHCR, OHNS, EN24 Materials

Dnyaneshwar. B. Unawane, K. J. Godihal

Share this Article

Similar Articles with Keyword 'Surface roughness'

Downloads: 111

Review Papers, Manufacturing Engineering, India, Volume 6 Issue 5, May 2017

Pages: 2014 - 2017

Review on Optimization Process Parameters of HCHCR, OHNS, EN24 Materials

Dnyaneshwar. B. Unawane, K. J. Godihal

Share this Article

Downloads: 120

Research Paper, Manufacturing Engineering, India, Volume 8 Issue 1, January 2019

Pages: 2191 - 2198

Performance of Cold Coolant for Machining of Inconel 718 using Carbide Cutting Tool

Selvarani P, Senthilkumaar J.S

Share this Article

Similar Articles with Keyword 'ANOVA'

Downloads: 109

Research Paper, Manufacturing Engineering, India, Volume 3 Issue 5, May 2014

Pages: 1011 - 1015

Parametric Optimization of TIG welding of Galvanized Steel with AA1050 using Taguchi Method

J. Pasupathy, V. Ravisankar, C. Senthilkumar

Share this Article

Downloads: 110

Research Paper, Manufacturing Engineering, India, Volume 6 Issue 4, April 2017

Pages: 2378 - 2382

Analysis of EDM Process Parameters for Optimization of Overcut per Side using Taguchi Techniques

A. D. Urade, V. S. Deshpande

Share this Article

Similar Articles with Keyword 'Taguchi Method'

Downloads: 109

Research Paper, Manufacturing Engineering, India, Volume 3 Issue 5, May 2014

Pages: 1011 - 1015

Parametric Optimization of TIG welding of Galvanized Steel with AA1050 using Taguchi Method

J. Pasupathy, V. Ravisankar, C. Senthilkumar

Share this Article

Downloads: 117

Review Papers, Manufacturing Engineering, India, Volume 4 Issue 5, May 2015

Pages: 2847 - 2850

Review on Optimization of Injection Molding Process Parameter for Reducing Shrinkage of High Density Polyethylene (HDPE) Material

Harshal P. Kale, Dr. Umesh V. Hambire

Share this Article
Top