International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064


Downloads: 126

Research Paper | Mechanical Engineering | China | Volume 4 Issue 3, March 2015


Finite Element Simulation for Cutting of Ti6AI4V

Lameck Sondo


Abstract: Titanium Ti6AI4V alloy is considered difficult to machine especially at higher cutting speeds, because of inherent properties such as low thermal conductivity, high chemical reactivity with cutting tool materials at elevated temperature, this leads to shorten the tool life and poor quality of the surface finishing of the workpiece being machined. By the use of Finite Element (FE) simulations have reduced the burden of extensive experimental trials in understanding the deformation behavior and optimize the cutting process. In this paper the finite element analysis (FEA) of machining for Ti6AI4V is presented. In this particular case the FEA is applied for both workpiece material and cutting tool material. Then at the end of this paper will be able to model and simulate, thereafter to study the influence of Cutting forces, cutting temperature and tool wear.


Keywords: Titanium Alloys Ti6AI4V, Finite Element Analysis FEA


Edition: Volume 4 Issue 3, March 2015,


Pages: 2318 - 2321


How to Cite this Article?

Lameck Sondo, "Finite Element Simulation for Cutting of Ti6AI4V", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=SUB152121, Volume 4 Issue 3, March 2015, 2318 - 2321

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'Finite Element Analysis FEA'

Downloads: 114

Research Paper, Mechanical Engineering, India, Volume 5 Issue 1, January 2016

Pages: 1541 - 1544

Thermal Modelling of a Marine Diesel Engine Piston

Jaedaa Abdulhamid, T.V.K. Bhanuprakash

Share this Article

Downloads: 124

Case Studies, Mechanical Engineering, India, Volume 4 Issue 9, September 2015

Pages: 1159 - 1165

Stress Optimization of S.I. Engine Piston

Rahul D. Raut, Satish Mishra

Share this Article

Similar Articles with Keyword 'Titanium'

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Downloads: 117

Research Paper, Mechanical Engineering, China, Volume 4 Issue 5, May 2015

Pages: 1862 - 1866

Laser Shock Forming of Titanium Alloy and Its Simulation Using Abaqus Finite Element Software

David Mbukwa

Share this Article

Similar Articles with Keyword 'Alloys'

Downloads: 0

Research Paper, Mechanical Engineering, Turkey, Volume 10 Issue 7, July 2021

Pages: 1327 - 1329

Investigation of the Effect of Normalization Process on Mechanical Properties and Microstructure of the AISI 4140 Alloy Steel

Yusuf YILMAZ, Ethem KESTI

Share this Article

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Similar Articles with Keyword 'Finite'

Downloads: 0

Review Papers, Mechanical Engineering, Ethiopia, Volume 10 Issue 7, July 2021

Pages: 483 - 486

Review on Structural Strength Analysis of Bogie Frame Based on Finite Element Method

Shihab Aldeen Mohammed Fadol

Share this Article

Downloads: 1

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 3, March 2015

Pages: 1426 - 1430

Modeling and Analysis of Human Liver by Using Finite Element Analysis

N. Kishore Kumar, K. Ashok Kumar Raju

Share this Article

Similar Articles with Keyword 'Element'

Downloads: 210

Research Paper, Mechanical Engineering, India, Volume 7 Issue 4, April 2018

Pages: 259 - 261

Self Flowing Generator

Batta Mahesh

Share this Article

Downloads: 0

Review Papers, Mechanical Engineering, Ethiopia, Volume 10 Issue 7, July 2021

Pages: 483 - 486

Review on Structural Strength Analysis of Bogie Frame Based on Finite Element Method

Shihab Aldeen Mohammed Fadol

Share this Article

Similar Articles with Keyword 'Analysis'

Downloads: 0

Review Papers, Mechanical Engineering, Ethiopia, Volume 10 Issue 7, July 2021

Pages: 483 - 486

Review on Structural Strength Analysis of Bogie Frame Based on Finite Element Method

Shihab Aldeen Mohammed Fadol

Share this Article

Downloads: 1

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 3, March 2015

Pages: 1426 - 1430

Modeling and Analysis of Human Liver by Using Finite Element Analysis

N. Kishore Kumar, K. Ashok Kumar Raju

Share this Article

Similar Articles with Keyword 'FEA'

Downloads: 236 | Weekly Hits: ⮙1 | Monthly Hits: ⮙3

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 478 - 481

Design and Development of Solar Powered Air Cooler

Vijaykumar Kalwa, Dr. R. Prakash

Share this Article

Downloads: 1

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 698 - 702

FEA of Double Shear Lug Joint by Varying Material Combinations

B. Vijaya Kumar, F. Anand Raju

Share this Article
Top