Research Paper | Mechanical Engineering | Libya | Volume 9 Issue 4, April 2020
Influence of Electrode Geometry in Parameters of Electrical Discharge Machining Process of AISID2 Tool Steel
Hanan S. Lahbishi, Ibrahim K. Husain, Shukry H. Aghdeab
Electrical Discharge Machining (EDM) is a non-traditional cutting process for metals removing based upon the fundamental fact that negligible tool force is generated during the machining process. Also, electrical discharge machining is used in manufacturing very hard materials that are electrically conductive. In this study, the effects of electrode geometry (tip radius and tip angles) with input parameters of EDM machining process such as (pulse current and pulse on time) on the output parameters like metal removal rate (MRR), electrode wear ratio (EWR), thickness of heat affected zone (HAZ) of machining of AISI D2 tool steel were investigated. The results of the experimental study are discussed in this paper. It is revealed that conical electrode with radius 1 mm gives highest MRR and the lowest EWR was with conical electrode with radius 0 mm as compared with the other electrodes, the results have indicated that the white layer thickness (WLT) increases with increase in electrode tip angle.
Keywords: Electrical Discharge Machining, Material Removal Rate, Electrode Wear Ratio, White Layer Thickness
Edition: Volume 9 Issue 4, April 2020
Pages: 883 - 889
How to Cite this Article?
Hanan S. Lahbishi, Ibrahim K. Husain, Shukry H. Aghdeab, "Influence of Electrode Geometry in Parameters of Electrical Discharge Machining Process of AISID2 Tool Steel", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=SR20305140618, Volume 9 Issue 4, April 2020, 883 - 889
94 PDF Views | 91 PDF Downloads
Similar Articles with Keyword 'Electrical Discharge Machining'
Review Papers, Mechanical Engineering, India, Volume 4 Issue 6, June 2015
Pages: 1385 - 1394Electrical Discharge Machining Characteristics of Aluminium Metal Matrix Composites - A Review
P. Srikanth, Ch. Pranay Kumar
Research Paper, Mechanical Engineering, India, Volume 6 Issue 7, July 2017
Pages: 1634 - 1637Effect of Machining Parameters in Electrical Discharge Machining of D2 Tool Steel
Raman K, Sathiya G K, Saisujith K, Mani P
Review Papers, Mechanical Engineering, India, Volume 4 Issue 12, December 2015
Pages: 821 - 824Review on Effect of Powder Mixed Dielectric on Material Removal Rate in Electric Discharge Machining
M. S. Bembde, J. K. Sawale
Research Paper, Mechanical Engineering, Libya, Volume 9 Issue 4, April 2020
Pages: 883 - 889Influence of Electrode Geometry in Parameters of Electrical Discharge Machining Process of AISID2 Tool Steel
Hanan S. Lahbishi, Ibrahim K. Husain, Shukry H. Aghdeab
Dissertation Chapters, Mechanical Engineering, India, Volume 2 Issue 1, January 2013
Pages: 431 - 436An Experimental Study on Parametric Optimization of High Carbon Steel (EN-31) by using Silicon Powder Mixed Dielectric EDM Process
Devdatt R. Vhatkar, B.R.Jadhav
Similar Articles with Keyword 'Material Removal Rate'
Research Paper, Mechanical Engineering, India, Volume 3 Issue 5, May 2014
Pages: 1248 - 1252Use of Artificial Neural Networks to Investigate the Surface Roughness in CNC Milling Machine
M. Vijay Kumar Reddy
Research Paper, Mechanical Engineering, India, Volume 8 Issue 10, October 2019
Pages: 521 - 526Optimization of Machining Parameters on Electric Discharge Machining (EDM) of Maraging Steels C300
Pottakarla Mahesh, Akkala Yakanna
Research Paper, Mechanical Engineering, India, Volume 6 Issue 7, July 2017
Pages: 1634 - 1637Effect of Machining Parameters in Electrical Discharge Machining of D2 Tool Steel
Raman K, Sathiya G K, Saisujith K, Mani P
Research Paper, Mechanical Engineering, India, Volume 6 Issue 5, May 2017
Pages: 2635 - 2638Milling Parameters Optimization for Better Surface Roughness and Material Removal Rate
Deepthi Haridasu, PrasadaRao Haridasu
Review Papers, Mechanical Engineering, India, Volume 4 Issue 12, December 2015
Pages: 821 - 824Review on Effect of Powder Mixed Dielectric on Material Removal Rate in Electric Discharge Machining
M. S. Bembde, J. K. Sawale