Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

Downloads: 98

Research Paper | Production Engineering | India | Volume 3 Issue 11, November 2014

Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process

K. G. Nikam, S. S. Kadam

Good surface quality is desired for the proper functioning of the produced parts. In the present study it was seen that the desired surface roughness were not obtained consistently in turning of EN 8 steel application (camshaft). These higher values of surface roughness results in rework and increases cost hence the main objective is optimization of surface roughness. Lots of optimization researches for finish turning were either accomplished within certain manufacturing purposes, or achieved through various equipment operations. Therefore, a general optimization of surface roughness is deemed to be necessary for the most of manufacturing industry. The surface quality is influenced by cutting speed, feed rate and depth of cut and many other parameters. In the present study attempt has been made to investigate the effect of cutting parameters (cutting speed, feed rate, depth of cut) and insert geometry (CNMG and TNMG type insert) on surface roughness in the finish turning of EN 8 steel. The experiments have been conducted using L9 orthogonal array in a SPEED LX 200 MAJOR CNC lathe machine. Turning process carried out on the EN 8 steel. The optimum cutting condition was determined surface roughness were evaluated by the analysis of variance (ANOVA).

Keywords: Turning, Surface roughness, insert geometry, ANOVA, Taguchi Method

Edition: Volume 3 Issue 11, November 2014

Pages: 1331 - 1335

Share this Article

How to Cite this Article?

K. G. Nikam, S. S. Kadam, "Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=OCT141235, Volume 3 Issue 11, November 2014, 1331 - 1335

Enter Your Email Address




Similar Articles with Keyword 'Turning'

Downloads: 98

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1331 - 1335

Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process

K. G. Nikam, S. S. Kadam

Share this Article

Downloads: 104 | Weekly Hits: ⮙1

Review Papers, Production Engineering, India, Volume 6 Issue 6, June 2017

Pages: 1448 - 1450

Optimization of CNC Machining Parameter of Al6061 to Improve Surface Roughness and Material Removal Rate: A Review

Virendrasinh Chavan, M. A. Sutar

Share this Article

Downloads: 107 | Weekly Hits: ⮙2 | Monthly Hits: ⮙10

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2637 - 2641

Analysis of Load Test Fixture Acting Under Static Loading Condition

Vineet V. Gosavi, Dr. K. H. Inamdar

Share this Article

Similar Articles with Keyword 'Surface roughness'

Downloads: 95

Research Paper, Production Engineering, India, Volume 6 Issue 3, March 2017

Pages: 2329 - 2335

Effect and Optimization of Process Parameters using Taguchi Method in WEDM for AISI M42 HSS Material

Joshi Guruprasad R., Dr. A. N. Chapgaon

Share this Article

Downloads: 98

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1331 - 1335

Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process

K. G. Nikam, S. S. Kadam

Share this Article

Downloads: 104 | Weekly Hits: ⮙1

Review Papers, Production Engineering, India, Volume 6 Issue 6, June 2017

Pages: 1448 - 1450

Optimization of CNC Machining Parameter of Al6061 to Improve Surface Roughness and Material Removal Rate: A Review

Virendrasinh Chavan, M. A. Sutar

Share this Article

Downloads: 107 | Weekly Hits: ⮙3

Research Paper, Production Engineering, India, Volume 6 Issue 8, August 2017

Pages: 1478 - 1482

Optimization of Quality and Accuracy in ECM Process with Hybrid Method

Pushpesh Dansena, Akshay Kumar

Share this Article

Downloads: 107

Research Paper, Production Engineering, India, Volume 8 Issue 10, October 2019

Pages: 1079 - 1083

Effect of Process Parameters during Machining of Mild Steel and Titanium

Ramcharan Vuyyala

Share this Article

Similar Articles with Keyword 'ANOVA'

Downloads: 95

Research Paper, Production Engineering, India, Volume 6 Issue 3, March 2017

Pages: 2329 - 2335

Effect and Optimization of Process Parameters using Taguchi Method in WEDM for AISI M42 HSS Material

Joshi Guruprasad R., Dr. A. N. Chapgaon

Share this Article

Downloads: 96 | Weekly Hits: ⮙2

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2721 - 2726

Application of Taguchi Method for Resistance Spot Welding of Stainless Steel-304 Grade

Manjunath R. Rawal, Dr. K. H. Inamdar

Share this Article

Downloads: 98

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1331 - 1335

Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process

K. G. Nikam, S. S. Kadam

Share this Article

Downloads: 100

Research Paper, Production Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1653 - 1657

Analysis of WEDM Parameters Using Taguchi Method

V. P. Baisane, Y. S. Sable, Hashmi A. Ahmed

Share this Article

Downloads: 104 | Weekly Hits: ⮙1

Review Papers, Production Engineering, India, Volume 6 Issue 6, June 2017

Pages: 1448 - 1450

Optimization of CNC Machining Parameter of Al6061 to Improve Surface Roughness and Material Removal Rate: A Review

Virendrasinh Chavan, M. A. Sutar

Share this Article

Similar Articles with Keyword 'Taguchi Method'

Downloads: 95

Research Paper, Production Engineering, India, Volume 6 Issue 3, March 2017

Pages: 2329 - 2335

Effect and Optimization of Process Parameters using Taguchi Method in WEDM for AISI M42 HSS Material

Joshi Guruprasad R., Dr. A. N. Chapgaon

Share this Article

Downloads: 96 | Weekly Hits: ⮙2

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2721 - 2726

Application of Taguchi Method for Resistance Spot Welding of Stainless Steel-304 Grade

Manjunath R. Rawal, Dr. K. H. Inamdar

Share this Article

Downloads: 98

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1331 - 1335

Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process

K. G. Nikam, S. S. Kadam

Share this Article

Downloads: 100

Research Paper, Production Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1653 - 1657

Analysis of WEDM Parameters Using Taguchi Method

V. P. Baisane, Y. S. Sable, Hashmi A. Ahmed

Share this Article

Downloads: 104 | Weekly Hits: ⮙1

Review Papers, Production Engineering, India, Volume 6 Issue 6, June 2017

Pages: 1448 - 1450

Optimization of CNC Machining Parameter of Al6061 to Improve Surface Roughness and Material Removal Rate: A Review

Virendrasinh Chavan, M. A. Sutar

Share this Article



Top