International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Most Trusted Research Journal Since Year 2012

ISSN: 2319-7064



Review Papers | Manufacturing Engineering | India | Volume 6 Issue 1, January 2017

A Review on Parameters Optimization of Tungsten Inert Gas Welding using Taguchi?s Design of Experiment Method

Jay Joshi, Manthan Thakkar

Tungsten Inert Gas welding is an important component in many industrial operations. The TIG welding parameters are the most important factors for the quality, productivity and cost of welding. This paper presents the influence of welding parameters like welding current, Gas Flow on strength of Aluminum material during welding. A plan of experiments and papers are based on Taguchis Design of Experiments technique (DOE). An Orthogonal array, signal to noise ratio and analysis of variance (ANOVA) are to investigate the welding characteristics of joint and optimize the welding parameters. Finally the conformations tests have been carried out to compare the predicted values with the experimental values to confirm its effectiveness in the analysis of strength. The main objective of industries reveal with producing better quality product at minimum cost and increase productivity. In the present paper an attempt is made to understand the effect of TIG welding parameters such as welding current, gas flow rate, welding speed that are influences on responsive output parameters such as hardness of welding, tensile strength of welding, by using optimization philosophy.

Keywords: Current, Gas Flow, Tungsten Inert Gas, ANOVA, DOE

Edition: Volume 6 Issue 1, January 2017

Pages: 2201 - 2203


How to Cite this Article?

Jay Joshi, Manthan Thakkar, "A Review on Parameters Optimization of Tungsten Inert Gas Welding using Taguchi?s Design of Experiment Method", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=NOV163714, Volume 6 Issue 1, January 2017, 2201 - 2203

38 PDF Views | 43 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'Current'

Research Paper, Manufacturing Engineering, India, Volume 3 Issue 5, May 2014

Pages: 1011 - 1015

Parametric Optimization of TIG welding of Galvanized Steel with AA1050 using Taguchi Method

J. Pasupathy, V. Ravisankar, C. Senthilkumar

Share this article

Research Paper, Manufacturing Engineering, India, Volume 4 Issue 3, March 2015

Pages: 1287 - 1290

Characteristic Study of Rapid Prototyped Parts at Different Build Orientation

Cany Mendonsa, KV Naveen, Prathik Upadhyaya

Share this article

Research Paper, Manufacturing Engineering, India, Volume 5 Issue 6, June 2016

Pages: 1366 - 1370

Interface Material for Enhancement of Weldability between Dissimilar Materials: 405 Ferritic Stainless Steel and 705 Zr Alloy by Friction Welding Process

K. Koundinya, A. Chennakesava Reddy

Share this article

Research Paper, Manufacturing Engineering, India, Volume 2 Issue 5, May 2013

Pages: 82 - 86

Effect of pulsed current on Welding characteristics of Aluminium alloy (5052) using Gas Tungsten Arc Welding

A.Raveendra, B.V.R.Ravi Kumar

Share this article

Review Papers, Manufacturing Engineering, India, Volume 5 Issue 1, January 2016

Pages: 996 - 999

Current Research and Development in Abrasive Water Jet Machining (AWJM): A Review

Sudhakar R. Lohar, Pravin R. Kubade

Share this article



Similar Articles with Keyword 'Tungsten Inert Gas'

Research Paper, Manufacturing Engineering, India, Volume 3 Issue 5, May 2014

Pages: 1011 - 1015

Parametric Optimization of TIG welding of Galvanized Steel with AA1050 using Taguchi Method

J. Pasupathy, V. Ravisankar, C. Senthilkumar

Share this article

Review Papers, Manufacturing Engineering, India, Volume 6 Issue 1, January 2017

Pages: 2201 - 2203

A Review on Parameters Optimization of Tungsten Inert Gas Welding using Taguchi?s Design of Experiment Method

Jay Joshi, Manthan Thakkar

Share this article



Similar Articles with Keyword 'ANOVA'

Research Paper, Manufacturing Engineering, India, Volume 3 Issue 5, May 2014

Pages: 1011 - 1015

Parametric Optimization of TIG welding of Galvanized Steel with AA1050 using Taguchi Method

J. Pasupathy, V. Ravisankar, C. Senthilkumar

Share this article

Comparative Studies, Manufacturing Engineering, India, Volume 4 Issue 3, March 2015

Pages: 1291 - 1294

Experimental Investigation on Surface Roughness in Finish Turning of EN 8 Steel

K. G. Nikam, S. V. Vanjari

Share this article

Research Paper, Manufacturing Engineering, India, Volume 4 Issue 2, February 2015

Pages: 330 - 333

Influence of FDM Process Parameters on Build Time Using Taguchi and ANOVA Approach

Cany Mendonsa, KV Naveen, Prathik Upadhyaya, Vyas Darshan Shenoy

Share this article

Research Paper, Manufacturing Engineering, India, Volume 6 Issue 4, April 2017

Pages: 2378 - 2382

Analysis of EDM Process Parameters for Optimization of Overcut per Side using Taguchi Techniques

A. D. Urade, V. S. Deshpande

Share this article

Review Papers, Manufacturing Engineering, India, Volume 6 Issue 1, January 2017

Pages: 2201 - 2203

A Review on Parameters Optimization of Tungsten Inert Gas Welding using Taguchi?s Design of Experiment Method

Jay Joshi, Manthan Thakkar

Share this article



Similar Articles with Keyword 'DOE'

Research Paper, Manufacturing Engineering, India, Volume 3 Issue 9, September 2014

Pages: 138 - 145

Trade Off Among Conflicting Multi Objectives of CNC End Milling Process for LM6 Al/SiCp

Neeraj Kumar, K. K. Chhabra

Share this article

Review Papers, Manufacturing Engineering, India, Volume 4 Issue 5, May 2015

Pages: 2847 - 2850

Review on Optimization of Injection Molding Process Parameter for Reducing Shrinkage of High Density Polyethylene (HDPE) Material

Harshal P. Kale, Dr. Umesh V. Hambire

Share this article

Research Paper, Manufacturing Engineering, India, Volume 4 Issue 5, May 2015

Pages: 722 - 725

Optimization of Injection Molding Process Parameter for Reducing Shrinkage by Using High Density Polyethylene (HDPE) Material

Harshal P. Kale, Dr. Umesh V. Hambire

Share this article

Research Paper, Manufacturing Engineering, India, Volume 6 Issue 1, January 2017

Pages: 1452 - 1455

Standard Time Study

Vibhor Gupta, Ayush Yajnik, Rahul Kadian, Vishal Sharma

Share this article

Research Paper, Manufacturing Engineering, India, Volume 6 Issue 4, April 2017

Pages: 2378 - 2382

Analysis of EDM Process Parameters for Optimization of Overcut per Side using Taguchi Techniques

A. D. Urade, V. S. Deshpande

Share this article
Top