Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

Downloads: 113 | Weekly Hits: ⮙2

Review Papers | Mechanical Engineering | India | Volume 5 Issue 4, April 2016

Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review

Sandip Kumar Das, Kedar Bhojak

The effect of oil temperature of the hydraulic system for Plastic Injection Moulding Machine is studied in this paper. Traditionally in India the hydraulic oil VG-68 for Plastic Injection Moulding Machine is used, which has an optimum temperature range with desired effective viscosity property is between 40C to 50C. The oil temperature goes high up to 55c and even higher than that during summer, which is not desirable for the machine operations. It is found that the operation of the machine will get sluggish as the oil viscosity get decreases. This is due to continuous flow and heavy production schedule. The oil needs to be cooled down as fast as possible from the elevated temperature to required temperature. So it is very important to choose the correct type and size of oil cooler for hydraulic system.

Keywords: Hydraulic system, VG-68, Plastic Injection Moulding Machine, Viscosity Grade oil, Heat Transfer Rate Increments, oil cooler

Edition: Volume 5 Issue 4, April 2016

Pages: 2266 - 2271

Share this Article

How to Cite this Article?

Sandip Kumar Das, Kedar Bhojak, "Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=NOV163211, Volume 5 Issue 4, April 2016, 2266 - 2271

Enter Your Registered Email Address





Similar Articles with Keyword 'Hydraulic system'

Downloads: 113 | Weekly Hits: ⮙3 | Monthly Hits: ⮙12

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 1457 - 1461

A Review on Possible Increment of Heat Transfer Rate for Hydraulic Oil Used in Plastic Injection Moulding Machine

Sandip Kumar Das, Kedar Bhojak

Share this Article

Downloads: 113 | Weekly Hits: ⮙2

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 2266 - 2271

Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review

Sandip Kumar Das, Kedar Bhojak

Share this Article

Downloads: 128 | Weekly Hits: ⮙5

Research Paper, Mechanical Engineering, India, Volume 9 Issue 7, July 2020

Pages: 1092 - 1093

Design of 20 Ton Hydraulic Press Machine for Flaring Operation

Viraj B. Ghangale

Share this Article

Downloads: 141 | Weekly Hits: ⮙4 | Monthly Hits: ⮙8

Research Paper, Mechanical Engineering, India, Volume 6 Issue 10, October 2017

Pages: 691 - 698

Design, Development & Analysis of Hydraulic Noise Suppressor

Sumit A. Nehere, Milind S. Ramgir

Share this Article

Similar Articles with Keyword 'VG-68'

Downloads: 113 | Weekly Hits: ⮙3 | Monthly Hits: ⮙12

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 1457 - 1461

A Review on Possible Increment of Heat Transfer Rate for Hydraulic Oil Used in Plastic Injection Moulding Machine

Sandip Kumar Das, Kedar Bhojak

Share this Article

Downloads: 113 | Weekly Hits: ⮙2

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 2266 - 2271

Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review

Sandip Kumar Das, Kedar Bhojak

Share this Article

Similar Articles with Keyword 'Plastic Injection Moulding Machine'

Downloads: 113 | Weekly Hits: ⮙3 | Monthly Hits: ⮙12

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 1457 - 1461

A Review on Possible Increment of Heat Transfer Rate for Hydraulic Oil Used in Plastic Injection Moulding Machine

Sandip Kumar Das, Kedar Bhojak

Share this Article

Downloads: 113 | Weekly Hits: ⮙2

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 2266 - 2271

Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review

Sandip Kumar Das, Kedar Bhojak

Share this Article

Similar Articles with Keyword 'Viscosity Grade oil'

Downloads: 113 | Weekly Hits: ⮙3 | Monthly Hits: ⮙12

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 1457 - 1461

A Review on Possible Increment of Heat Transfer Rate for Hydraulic Oil Used in Plastic Injection Moulding Machine

Sandip Kumar Das, Kedar Bhojak

Share this Article

Downloads: 113 | Weekly Hits: ⮙2

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 2266 - 2271

Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review

Sandip Kumar Das, Kedar Bhojak

Share this Article

Similar Articles with Keyword 'Heat Transfer Rate Increments'

Downloads: 113 | Weekly Hits: ⮙3 | Monthly Hits: ⮙12

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 1457 - 1461

A Review on Possible Increment of Heat Transfer Rate for Hydraulic Oil Used in Plastic Injection Moulding Machine

Sandip Kumar Das, Kedar Bhojak

Share this Article

Downloads: 113 | Weekly Hits: ⮙2

Review Papers, Mechanical Engineering, India, Volume 5 Issue 4, April 2016

Pages: 2266 - 2271

Oil Cooler Selection for Hydraulic System of Plastic Injection Moulding Machine: A Review

Sandip Kumar Das, Kedar Bhojak

Share this Article



Top