International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064

Downloads: 117 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Research Paper | Mechanical Engineering | India | Volume 5 Issue 3, March 2016

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Friction Stir Welding (FSW) is considered to be the most significant development in metal joining technologies to join high strength aerospace aluminum alloys. In order to improve the reliability and quality of the products manufactured by FSW process input process parameters such as tool rotational speed, welding speed and axial force are to be optimized. This study deals with the optimization of process parameters for the FSW by employing the Taguchi Design of Experiment (DOE) methodology to experimentally evaluate optimum weld strength and hardness on aluminum alloy. L-9 and L-27 orthogonal arrays of Taguchi was used to analyze and determine the optimal condition, the results were put to S/N analysis and Analysis of Variance (ANOVA) to find the significant welding parameters affecting the weld quality. Using ANOVA the significant factors were determined for each welding performance criteria, such as the Tensile strength. Statistical analysis of variance (ANOVA) was performed to identify the significant parameters. It is observed that Maximum Tensile strength is exhibited by FSW joints with the optimal parameters as Tool Rotational speed (A) of 1200 rpm, Welding speed (B) of 40 mm/min and Axial force of 4 KN.

Keywords: Taguchi Design, Friction Stirs, Welding, Aluminum, Alloys

Edition: Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Share this Article

How to Cite this Article?

Siva Rama Krishna R, Pavan Kumar T, "Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=NOV162391, Volume 5 Issue 3, March 2016, 1988 - 1994

Enter Your Email Address


Similar Articles with Keyword 'Taguchi Design'

Downloads: 116 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 6 Issue 11, November 2017

Pages: 1833 - 1842

An Experimental Investigation and Optimization of Electrical Discharge Drilling for Small Hole Drilling with High Aspect Ratio

Ashok Kumar, Sandeep Kumar Rawal

Share this Article

Downloads: 132

Research Paper, Mechanical Engineering, India, Volume 2 Issue 6, June 2013

Pages: 462 - 465

Tribological Characterisation and Morphological Study of Epoxy Composites filled with WS2 under Dry Sliding

M. H. Shaikh, G. J. Pawar, J. S. Sidhu

Share this Article

Similar Articles with Keyword 'Welding'

Downloads: 107

Research Paper, Mechanical Engineering, India, Volume 4 Issue 4, April 2015

Pages: 1396 - 1399

Thermo-Mechanical Analysis in TIG Welding of Aluminium Alloy 6082

Swapnil S. Ingle, Dr. Rajendra S. Dalu

Share this Article

Downloads: 112

Review Papers, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 2002 - 2008

Optimization of Process Parameters for Resistance Spot Welding Process of HR E-34 Using Response Surface Method ? A Review

B. S. Gawai, Dr. C. M. Sedani

Share this Article

Similar Articles with Keyword 'Aluminum'

Downloads: 111

Research Paper, Mechanical Engineering, India, Volume 4 Issue 8, August 2015

Pages: 1359 - 1364

Modification of Straight Bladed Hallow Cored Wind Turbine Through Experimental Analysis

R. Sree Vasthava, K. Ashok Kumar

Share this Article

Downloads: 111

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 11, November 2015

Pages: 1411 - 1417

Design Optimization of Passenger Car Front Bumper

Manideep Kumar Vandanapu, Ratnakar Pandu

Share this Article

Similar Articles with Keyword 'Alloys'

Downloads: 0

Research Paper, Mechanical Engineering, Turkey, Volume 10 Issue 7, July 2021

Pages: 1327 - 1329

Investigation of the Effect of Normalization Process on Mechanical Properties and Microstructure of the AISI 4140 Alloy Steel

Yusuf YILMAZ, Ethem KESTI

Share this Article

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Similar Articles with Keyword 'Taguchi'

Downloads: 104

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1509 - 1515

Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis

D.U.M. Manikanta, A. Chennakesava Reddy

Share this Article

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Similar Articles with Keyword 'Design'

Downloads: 231 | Monthly Hits: ⮙1

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 478 - 481

Design and Development of Solar Powered Air Cooler

Vijaykumar Kalwa, Dr. R. Prakash

Share this Article

Downloads: 0

Research Paper, Mechanical Engineering, India, Volume 10 Issue 6, June 2021

Pages: 1423 - 1428

Improvement in Performance of Heat Exchanger by using Promoters

Saurabh D Vighe, VG Gore

Share this Article

Similar Articles with Keyword 'Friction'

Downloads: 1

Review Papers, Mechanical Engineering, India, Volume 10 Issue 5, May 2021

Pages: 624 - 626

Air Bearings-Application Review

Sakshi Potdar, Srinidhi Campli

Share this Article

Downloads: 34

Research Paper, Mechanical Engineering, Turkey, Volume 10 Issue 3, March 2021

Pages: 1700 - 1704

Modeling of Recoil Motion of Heavy Weapons with Hydropneumatic Recoil Mechanism

Ibrahim Turkmen, Veli Celik

Share this Article
Top