Research Paper | Mechanical Engineering | India | Volume 5 Issue 1, January 2016
Comparative Studies of Heat Flow Rate in the Catalytically Activated Two Stroke SI Engine Components over Base Engine by FEA
Dr. K. Kishor
Knowledge on heat flow rate across the piston, liner and cylinder head of an engine is highly essential for a designer for arriving at a reasonable configuration of the piston, liner and cylinder head without sacrificing the strength. Heat flow rate across the piston, liner and cylinder head of CE (Conventional Engine, referred as Base Engine) and CCE (Copper Coated Engine, referred as Catalytic Coated Engine/Catalytically Activated Engine) was determined to study the performance of lubricating oil. The prediction of percentage increase of heat flow with the help of finite element analysis (FEA) using ANSYS software package is important, in these components, which determines the efficient combustion by means of catalytic coating on the surface of piston crown and over the inside surface of cylinder head. These studies are conducted on CE and also on CCE in order to emphasize the advantage of CCE over CE in producing efficient combustion. The heat flux rate was found to be increasing along both axis and radius of piston, liner and cylinder head of CCE over CE.
Keywords: Copper coating, base engine, heat flow rate, FEA, ANSYS
Edition: Volume 5 Issue 1, January 2016
Pages: 1394 - 1397
How to Cite this Article?
Dr. K. Kishor, "Comparative Studies of Heat Flow Rate in the Catalytically Activated Two Stroke SI Engine Components over Base Engine by FEA", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=NOV153130, Volume 5 Issue 1, January 2016, 1394 - 1397
17 PDF Views | 21 PDF Downloads
Video Lecture of Above Article is Not Available Yet
You be the First to Request! Press the Button below!
Similar Articles with Keyword 'Copper coating'
Research Paper, Mechanical Engineering, India, Volume 5 Issue 1, January 2016
Pages: 1391 - 1393Analysis of Exhaust Emissions from Two Stroke Spark Ignition Engine with Copper Coated Piston Operating with Methyl Alcohol Blended Gasoline
Dr. K. Kishor
Research Paper, Mechanical Engineering, India, Volume 5 Issue 1, January 2016
Pages: 1394 - 1397Comparative Studies of Heat Flow Rate in the Catalytically Activated Two Stroke SI Engine Components over Base Engine by FEA
Dr. K. Kishor
Similar Articles with Keyword 'heat flow rate'
Research Paper, Mechanical Engineering, India, Volume 5 Issue 1, January 2016
Pages: 1394 - 1397Comparative Studies of Heat Flow Rate in the Catalytically Activated Two Stroke SI Engine Components over Base Engine by FEA
Dr. K. Kishor
Research Paper, Mechanical Engineering, India, Volume 7 Issue 2, February 2018
Pages: 1179 - 1182Experimentation on Double Pipe Heat Exchanger Using Water and Nanofluid
J. Emeema, C. Lakshmi Sindhuja, K. Laxman
Similar Articles with Keyword 'FEA'
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 11, November 2014
Pages: 698 - 702FEA of Double Shear Lug Joint by Varying Material Combinations
B. Vijaya Kumar, F. Anand Raju
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 7, July 2014
Pages: 1168 - 1172Design, Synthesis and Development of Adaptable Multi-postured Chair for ATM Security Personnel
Vinod Kumar R., Praveen M. P.
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 8, August 2014
Pages: 950 - 954Fatigue Life Estimation of Fuselage Structure Due to Fluctuating Bending Loads
Mallikarjun, Vidyadhar Pujar
Research Paper, Mechanical Engineering, India, Volume 5 Issue 11, November 2016
Pages: 1624 - 1627Effect of Contact Parameters on the Accuracy and Computational Efficiency of Finite Element Analysis in the Interference Analysis
Bharat Panjwani
Review Papers, Mechanical Engineering, India, Volume 4 Issue 2, February 2015
Pages: 2341 - 2344A Review of Optimized Heat Treatment for Bearing Cup in Drive Shaft Assembly
D. R. Lahore, R. A. Kathar
Similar Articles with Keyword 'ANSYS'
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 3, March 2015
Pages: 1426 - 1430Modeling and Analysis of Human Liver by Using Finite Element Analysis
N. Kishore Kumar, K. Ashok Kumar Raju
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 8, August 2016
Pages: 1539 - 1543Analysis of Cracks Starting from a Square Hole in a Rectangular Plate
S. M. Rajmane, Shailesh Birajdar
Research Paper, Mechanical Engineering, India, Volume 4 Issue 5, May 2015
Pages: 2857 - 2861Analysis of Heat Transfer in Turbulent Channel Using Grooves
Mayank Bhola, Dr. Satyendra Singh
M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 9, September 2015
Pages: 1298 - 1305Investigation of Drag and Lift Forces over the Profile of Car with Rearspoiler Using CFD
V. Naveen Kumar, Dr. K. Lalit Narayan, L. N. V. Narasimha Rao, Y. Sri Ram
Research Paper, Mechanical Engineering, India, Volume 6 Issue 6, June 2017
Pages: 1164 - 1166Model Designing and Acoustic Analysis of Muffler with Baffles for Four Stroke Diesel Engine
Deepthi Haridasu, PrasadaRao Haridasu