International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064




Downloads: 117

Dissertation Chapters | Manufacturing Engineering | India | Volume 2 Issue 5, May 2013


Determination of Effects of Various Parameters on Forming Limit Diagram using FEA

R. J. Bhat


Abstract: Sheet metal forming is the process of converting flat sheet of metal into a part of desired shape without fracture or excessive localized thinning and widely used in aerospace, automotive, appliances industry. In sheet metal forming failure can be predicted by Forming Limit Diagram (FLD). FLD offers a convenient and useful tool in sheet products manufacturing analysis. They show the critical combinations of major strain and minor strain in the sheet surface at the onset of necking and are also used during the design stage of any new sheet metal component for tooling shape for optimizing process variables of new product development. In this research, the effect of n-value (strain hardening exponent), punch velocity & sheet thickness on FLD were studied using FE based HYPERFORM software. As new market requirements are becoming more persistence through introduction of new technologies for improvements in performance trends, these FEM based software simulation is becoming more affordable & reliable as they reduce lead time & cost. It also improves productivity & quality. A typical industrial component was chosen for analysis. The results demonstrate that FLD0 increases with increasing n-value & sheet thickness but for punch velocity more iteration are required


Keywords: Computer Simulation, Forming Limit Diagram, Parameters, Sheet Metal Forming


Edition: Volume 2 Issue 5, May 2013,


Pages: 101 - 103


How to Cite this Article?

R. J. Bhat, "Determination of Effects of Various Parameters on Forming Limit Diagram using FEA", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=IJSRON2013965, Volume 2 Issue 5, May 2013, 101 - 103

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'Parameters'

Downloads: 91

Informative Article, Manufacturing Engineering, India, Volume 8 Issue 12, December 2019

Pages: 1845 - 1848

Fabrication of Folded Wave Guide Structure by Laser Micromachining

Mounashree B S, Mr Sudhir B S

Share this Article

Downloads: 93

Research Paper, Manufacturing Engineering, India, Volume 5 Issue 6, June 2016

Pages: 1138 - 1143

Single Point Incremental Forming of AA1050-H18 Alloy Frustum of Cone Cups

V. Srija, A. Chennakesava Reddy

Share this Article

Similar Articles with Keyword 'Computer'

Downloads: 109

Survey Paper, Manufacturing Engineering, India, Volume 4 Issue 12, December 2015

Pages: 2285 - 2288

An Overview on the Trends and Challenges of Advanced Manufacturing

N. Sivasubramanian, Prof S. Sheik Mohamed

Share this Article

Downloads: 128

Review Papers, Manufacturing Engineering, India, Volume 5 Issue 3, March 2016

Pages: 905 - 911

A Strategic and Hierarchical Approach to Implement a Flexible Manufacturing System (FMSs), its Scope and Applications: An Overview

S. C. Ram, A. K. Mandal

Share this Article

Similar Articles with Keyword 'Simulation'

Downloads: 91

Informative Article, Manufacturing Engineering, India, Volume 8 Issue 12, December 2019

Pages: 1845 - 1848

Fabrication of Folded Wave Guide Structure by Laser Micromachining

Mounashree B S, Mr Sudhir B S

Share this Article

Downloads: 100

Research Paper, Manufacturing Engineering, China, Volume 5 Issue 1, January 2016

Pages: 1505 - 1508

Simulation and Optimization of Aviation Integral Impeller Machining Based on VERICUT

Hui Lu, Yujun Cai, Guohe Li

Share this Article

Similar Articles with Keyword 'Forming'

Downloads: 93

Research Paper, Manufacturing Engineering, India, Volume 5 Issue 6, June 2016

Pages: 1138 - 1143

Single Point Incremental Forming of AA1050-H18 Alloy Frustum of Cone Cups

V. Srija, A. Chennakesava Reddy

Share this Article

Downloads: 102

Research Paper, Manufacturing Engineering, China, Volume 5 Issue 3, March 2016

Pages: 1487 - 1490

Springback Simulation of U-channel Forming Process based on Finite Element Analysis

Altaye Girum Temechache, Prof. Men Changfeng, Lie Duan, Han Chui Hong

Share this Article

Similar Articles with Keyword 'Limit'

Downloads: 92

Research Paper, Manufacturing Engineering, Kenya, Volume 5 Issue 11, November 2016

Pages: 1964 - 1966

Challenges Faced in the Implementation of Supply Chain Management in the Manufacturing Sector

William K. Koech, Richard K. Ronoh

Share this Article

Downloads: 126

Research Paper, Manufacturing Engineering, China, Volume 4 Issue 7, July 2015

Pages: 420 - 427

Weld Design of Vehicle Bodies and Analysis of Welded Butt and T-joints Using Simufact

Hailemariam Fisseha Nega, Yang Hui, Gao Ying

Share this Article
Top