Optimization Performance of a Robot to Reduce Cycle Time Estimate
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

Dissertation Chapters | Mechanical Engineering | India | Volume 2 Issue 3, March 2013

Optimization Performance of a Robot to Reduce Cycle Time Estimate

Pratik P. Gandhi, A. K. Jain

In some daily tasks such as Pick and Place or Loading and Unloading application, the Cartesian robot is requested to reach with its end-effector to a desired target location. Such tasks become more complex if it has to handle multiple points in shortest travelling time and space. It this reasons that there study was conducted with the primary objective to develop a computational intelligent system that would contribute towards encouraging a productive and quality way of material handling and processing. The objective of this paper is to optimize the performance of a Cartesian (Gantry) robot to pick hot crown gear in a quenching press machine and to place our Tray Track line pallate board by Cartesian (Gantry) robot used of end-effector. In this paper where actual robot perform in an automobile industries where some distance parameter taken, there used for Aichelin Software are perform of Cartesian Robot movement used. But now in this replace on based the C++ programming & Matlab Software. We calculated our Actual Robot Cycle Time & Estimated new Cycle time to increase the productivity and increase the Efficiency of a industries.

Keywords: Programming, Pick and Place movement, Cycle Time, Estimation

Edition: Volume 2 Issue 3, March 2013

Pages: 357 - 363

Share this Article

How to Cite this Article?

Pratik P. Gandhi, A. K. Jain, "Optimization Performance of a Robot to Reduce Cycle Time Estimate", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=IJSRON2013576, Volume 2 Issue 3, March 2013, 357 - 363

86 PDF Views | 77 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'Programming'

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 5, May 2016

Pages: 1984 - 1989

Study the Effects of Free Vibration and Effective Elastic Properties with Variation of Layer Orientation of Symmetric Laminate Plates

K. Pradeep Chand, K. Chaitanya

Share this Article

Research Paper, Mechanical Engineering, China, Volume 6 Issue 7, July 2017

Pages: 1714 - 1719

Experimental Study of Diesel Engine Power Test Based on the No-Load Power Measuring

Xiaohua Xiao, Yuheng Li, Jiajia Jing, Wenquan Wang

Share this Article

Research Paper, Mechanical Engineering, India, Volume 7 Issue 6, June 2018

Pages: 1601 - 1608

Analysis and Modeling of Flexible Manufacturing System

Adarsh Kumar Pandey, Shiv Kumar Tripathi

Share this Article

Dissertation Chapters, Mechanical Engineering, India, Volume 2 Issue 3, March 2013

Pages: 357 - 363

Optimization Performance of a Robot to Reduce Cycle Time Estimate

Pratik P. Gandhi, A. K. Jain

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 7, July 2014

Pages: 2310 - 2317

Programming of HC900 Controller based Speed Control System for D.C. Motor

L. B. Raut, P. K.Parase, Suraj Jagtap

Share this Article

Similar Articles with Keyword 'Cycle Time'

Research Paper, Mechanical Engineering, India, Volume 4 Issue 11, November 2015

Pages: 1997 - 2001

Cycle Time Reduction to Increase Productivity of DVD Production

Hasibur Rahaman, Suman Nihar, Habib Masum

Share this Article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 2, February 2016

Pages: 1706 - 1710

Comparative Study of Heat Absorbing Packed Bed Regenerator for Space Heating Using Clay And Waste Hard Rubber for Long Term Heat Storage

Shivasheesh Kaushik, Dr. Anirudh Gupta

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 3, March 2014

Pages: 807 - 811

Assembly Line Balancing - A Review

Vrittika Pachghare, R. S. Dalu

Share this Article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 5, May 2015

Pages: 3198 - 3205

Experimental Study of Heat Absorbing Packed Bed Regenerator for Space Heating for Industrial Purpose

Shivasheesh Kaushik, Dr. Anirudh Gupta

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 5, May 2014

Pages: 1636 - 1639

Molten Metal Flow Analysis of Housing Component

Bodhayana M. R., N Ramesha

Share this Article

Similar Articles with Keyword 'Estimation'

Review Papers, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 651 - 653

Evaluation of Fatigue Failure of Crankshaft Work on its Bearing and Crank Pin Analytically and Numerically - A Review

Suryakant Rathod, Qaimi Mudassar

Share this Article

Research Paper, Mechanical Engineering, India, Volume 8 Issue 8, August 2019

Pages: 1004 - 1013

Hot and Cold Utilities in Plant Containing Multiple Heat Exchanger Networks

G Pradeep

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 8, August 2014

Pages: 950 - 954

Fatigue Life Estimation of Fuselage Structure Due to Fluctuating Bending Loads

Mallikarjun, Vidyadhar Pujar

Share this Article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 2, February 2016

Pages: 1975 - 1978

Estimation of Heat Transfer Coefficient and Pressure Drop in a Solar Collector Using Fresnel Lenses

Prakash R. Tripathi, Mahesh G. Bhong

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 4, April 2014

Pages: 389 - 390

Estimation of Flexural Strength and Shear Strength of Sandwich Panel by Varying Foam Density

Aniber Benin.M, Dilip Thomas

Share this Article
Top