International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Most Trusted Research Journal Since Year 2012

ISSN: 2319-7064

Research Paper | Mechanical Engineering | India | Volume 2 Issue 1, January 2013

Some Tribological Investigations on Zinc Base Alloy

Vijaykumar N Chalwa, Nishal Kadli

ZA-27 alloys reinforced by Mn-containing intermetallic compounds were prepared and effect of Mn content on impact strength, hardness, tensile strength, volumetric wear rate and surface roughness were examined. By adding Mn, Si, Cu, Mg into ZA-27, experimental alloys were fabricated by gravity die casting. The volume fraction and grain size of the Mn-containing inter metallic compound phases vary with the changing of Mn content. As the percentage of Mn increases the volume fraction and size of the precipitates increased. Volumetric wear rate of the reinforced ZA-27 alloys at room temperature were measured. The results show that the impact strength and hardness values are increased with increase in Mn up to 1 %. Ultimate tensile strength and Volumetric wear rate decreased with increase in Mn up to 1 %. But surface roughness is decreases almost with increase in the Mn content. Bettertribological properties of these alloys can be achieved at a Mn content of 1 %.

Keywords: ZA-27, Inter metallic compounds, Impact strength, Hardness, Tensile strength, volumetric wear rate, Surface roughness

Edition: Volume 2 Issue 1, January 2013

Pages: 341 - 344


How to Cite this Article?

Vijaykumar N Chalwa, Nishal Kadli, "Some Tribological Investigations on Zinc Base Alloy", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=IJSR13010214, Volume 2 Issue 1, January 2013, 341 - 344

23 PDF Views | 15 PDF Downloads

Download Article PDF

Video Lecture of Above Article is Not Available Yet

You be the First to Request! Press the Button below!



Similar Articles with Keyword 'Impact strength'

Research Paper, Mechanical Engineering, Nigeria, Volume 6 Issue 6, June 2017

Pages: 2314 - 2318

Potential of Hot Sesame Oil (sesanum indicum oil) Bath as Quenchant for Austempering of Ductile Cast Iron

Shehu Abdulhamid, Yohanna Mbudai, Rayyan Dodo

Share this article

Research Paper, Mechanical Engineering, India, Volume 8 Issue 8, August 2019

Pages: 2174 - 2177

Effect of Quenching Media on Mechanical Properties of 7075 Aluminium Alloy

P. Senthilkumar

Share this article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 8, August 2014

Pages: 585 - 588

Study on Mechanical Characteristics of Unidirectional Sisal/Glass Fiber Reinforced Polyester Hybrid Composites

Sanjay.M.R, Arpitha.G.R, Vasundhara.M.G, B.Yogesha

Share this article

Research Paper, Mechanical Engineering, India, Volume 2 Issue 1, January 2013

Pages: 341 - 344

Some Tribological Investigations on Zinc Base Alloy

Vijaykumar N Chalwa, Nishal Kadli

Share this article

Similar Articles with Keyword 'Hardness'

Research Paper, Mechanical Engineering, Egypt, Volume 6 Issue 10, October 2017

Pages: 559 - 565

Micro Investigation into Positron Annihilation, Tribological and Mechanical Properties of Compacted Zn, ZnO2 and Zn-ZSM-5 Nano Powders

Hala M. Abo-Dief

Share this article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 8 Issue 12, December 2019

Pages: 1622 - 1629

Some Investigations on Drilling of Aluminium Based Metal Matrix Composites

Vinodkumar M. Chandankar, Aarti A. Dyade

Share this article

Research Paper, Mechanical Engineering, India, Volume 7 Issue 5, May 2018

Pages: 1529 - 1532

Experimental Investigation of Low Velocity Impact on Hybrid Composite

Divyank Dubey, Dharamvir Mangal

Share this article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 2, February 2017

Pages: 744 - 749

Study of the Effect of Electro-co-deposition on Transmission Gears

B S Praveen Kumar, K M Narayanappa

Share this article

Similar Articles with Keyword 'Tensile strength'

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1509 - 1515

Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis

D.U.M. Manikanta, A. Chennakesava Reddy

Share this article

Review Papers, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 2449 - 2452

A Review on Optimizing Process Parameters for TIG Welding using Taguchi Method & Grey Relational Analysis

Imran A. Shaikh, M. Veerabhadra Rao

Share this article

Research Paper, Mechanical Engineering, Nigeria, Volume 6 Issue 6, June 2017

Pages: 2314 - 2318

Potential of Hot Sesame Oil (sesanum indicum oil) Bath as Quenchant for Austempering of Ductile Cast Iron

Shehu Abdulhamid, Yohanna Mbudai, Rayyan Dodo

Share this article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 1, January 2017

Pages: 1440 - 1444

Ergonomically Design of Multipurpose Portable Wooden Table

D. R. Thawkar

Share this article

Similar Articles with Keyword 'Surface roughness'

Research Paper, Mechanical Engineering, Nigeria, Volume 4 Issue 7, July 2015

Pages: 2030 - 2036

Cutting Parameters Effects on Surface Roughness During End Milling of Aluminium 6061 Alloy Under Dry Machining Operation

Okokpujie Imhade. P, Okonkwo Ugochukwu.C, Okwudibe Chinenye. D.

Share this article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 6 Issue 6, June 2017

Pages: 440 - 445

Comparative Assessment of Carbide Insert and Cermet Insert on Surface Roughness in Boring of ASTM A48 Grey Cast Iron

Ajay Sankar, Soumyalata.D

Share this article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 9, September 2017

Pages: 913 - 916

Pulsed Laser Micro Polishing of Metals Using Dual-Beam Technology

Lagad Rahul Anil, Dr. Ashwini Kumar

Share this article

Research Paper, Mechanical Engineering, India, Volume 9 Issue 3, March 2020

Pages: 1186 - 1190

Use of Vegetable Oil as Cutting Fluid in Turning of Mild Steel with MQL and Optimization of Cutting Parameter

Bramhane R S, Pawar D S

Share this article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 7, July 2015

Pages: 1091 - 1095

Multi Objective Optimization of Cutting Parameter in EDM Using Grey Taguchi Method

D. Venkatesh Naik, Dr. D. R. Srinivasan

Share this article

Top