Microstructure Analysis of the Carbon Nano Tubes-Aluminum Composite with different Manufacturing Conditions
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

Research Paper | Mechanical Engineering | Ethiopia | Volume 1 Issue 3, December 2012

Microstructure Analysis of the Carbon Nano Tubes-Aluminum Composite with different Manufacturing Conditions

Balamurugan Adhithan, Hari Prasada Rao Pydi

The interest in carbon nano tubes (CNTs) as reinforcements for aluminum (Al) has been growing considerably. Efforts have been largely focused on investigating their contribution to the enhancement of the mechanical performance of the composites. The uniform dispersion of CNTs in the Al matrix has been identified as being critical to the pursuit of enhanced properties. Stir Casting method as a mechanical dispersion technique has proved its potential. In this work, we use Stir casting method to disperse up to 4 wt. % CNT in an Al matrix. The effect of CNT content on the Physical properties of the composites like SEM, XRD was investigated. The improvement of physical properties for composites of Al CNT has been compared with pure aluminum [1100].

Keywords: Scanning electron microscope, XRD, Carbon Nano tubes, Aluminum

Edition: Volume 1 Issue 3, December 2012

Pages: 153 - 158

Share this Article

How to Cite this Article?

Balamurugan Adhithan, Hari Prasada Rao Pydi, "Microstructure Analysis of the Carbon Nano Tubes-Aluminum Composite with different Manufacturing Conditions", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=IJSR13010103, Volume 1 Issue 3, December 2012, 153 - 158

143 PDF Views | 132 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'XRD'

| Weekly Popularity: ⮙4

Research Paper, Mechanical Engineering, Libya, Volume 7 Issue 12, December 2018

Pages: 1529 - 1530

Thermal Treatment of Sol-gel Titania Films Deposited on Stainless Steel for Surface Improvement

Blgasam Omer Eissa Al-Sharef, Ahmed.O.Mohamed

Share this Article

| Weekly Popularity: ⮙3

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 9, September 2014

Pages: 426 - 431

Characterization, AC Conductivity and Dielectric behaviour of Chemically Synthesized Poly Meta-Aminophenol

Dr. Shantharaja M., Srinivas K. R.

Share this Article

Research Paper, Mechanical Engineering, Ethiopia, Volume 1 Issue 3, December 2012

Pages: 153 - 158

Microstructure Analysis of the Carbon Nano Tubes-Aluminum Composite with different Manufacturing Conditions

Balamurugan Adhithan, Hari Prasada Rao Pydi

Share this Article

| Weekly Popularity: ⮙3

Research Paper, Mechanical Engineering, India, Volume 6 Issue 2, February 2017

Pages: 744 - 749

Study of the Effect of Electro-co-deposition on Transmission Gears

B S Praveen Kumar, K M Narayanappa

Share this Article

Similar Articles with Keyword 'Aluminum'

| Weekly Popularity: ⮙5

Research Paper, Mechanical Engineering, India, Volume 4 Issue 8, August 2015

Pages: 1359 - 1364

Modification of Straight Bladed Hallow Cored Wind Turbine Through Experimental Analysis

R. Sree Vasthava, K. Ashok Kumar

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 11, November 2015

Pages: 1411 - 1417

Design Optimization of Passenger Car Front Bumper

Manideep Kumar Vandanapu, Ratnakar Pandu

Share this Article

| Weekly Popularity: ⮙5

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this Article

Research Paper, Mechanical Engineering, Iraq, Volume 4 Issue 9, September 2015

Pages: 1781 - 1789

A Comparison of the Heat Transfer Performance of a Hexagonal Pin Fin with Other Types of Pin Fin Heat Sinks

Eaman Hassan Muhammad

Share this Article

| Weekly Popularity: ⮙3

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 2, February 2016

Pages: 1412 - 1415

Modeling and Analysis of a Shaft Blade for its Strength

A. Satya Dinesh, G. V. Naga Mani

Share this Article
Top