Some Investigations on Drilling of Aluminium Based Metal Matrix Composites
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064


Amazon Sale


M.Tech / M.E / PhD Thesis | Mechanical Engineering | India | Volume 8 Issue 12, December 2019

Some Investigations on Drilling of Aluminium Based Metal Matrix Composites

Vinodkumar M. Chandankar, Aarti A. Dyade

In this study, Drilling is a metal removal process and is important for the final fabrication stage prior to application. This paper discusses the influence of cutting parameters on drilling characteristics of metal matrix composites (MMCs) Al6061/SiC320grit. The composites are fabricated using stir casting method. In order to determine the mechanical properties of the produced composites, hardness and tensile tests were performed. Moreover, the effects of the machining parameters such as cutting speed, feed rate, particle fraction and cutting-tool material, and of their interactions on the thrust force and cutting torque were determined by means of Taguchi experimental design. In addition the drilling parameters were optimized in terms of cutting forces (thrust force and torque). Furthermore, an analysis of variance (ANOVA) was conducted to obtain the degree of the effect of the parameters. Therefore, the most influential control factor for the cutting forces was found to be the particle fraction and feed rate. According to the experimental results, the thrust force and cutting torque increased significantly with increasing the feed rate or the particle content. On the other hand, the influence of the drill-bit material and the interactions of the factors for the cutting forces were quite low.

Keywords: MMC, Stir casting, drilling

Edition: Volume 8 Issue 12, December 2019

Pages: 1622 - 1629

Share this Article

How to Cite this Article?

Vinodkumar M. Chandankar, Aarti A. Dyade, "Some Investigations on Drilling of Aluminium Based Metal Matrix Composites", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=ART20203677, Volume 8 Issue 12, December 2019, 1622 - 1629

81 PDF Views | 62 PDF Downloads

Download Article PDF


Amazon Sale


Similar Articles with Keyword 'MMC'

Research Paper, Mechanical Engineering, India, Volume 6 Issue 6, June 2017

Pages: 2025 - 2030

Analysis on Mechanical Behaviour of AA 1050/ SiC and AA 1050/Al2O3 Composites

Kapil Singh, Mukesh Kumar

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 8, August 2014

Pages: 1032 - 1036

Weight Optimization of Connecting Rod by Al-Si Metal Matrix Reinforced With Alumina and Flyash

Fayaz Kandagal, Bhimagoud Patil

Share this Article

Review Papers, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1385 - 1394

Electrical Discharge Machining Characteristics of Aluminium Metal Matrix Composites - A Review

P. Srikanth, Ch. Pranay Kumar

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 8 Issue 12, December 2019

Pages: 1622 - 1629

Some Investigations on Drilling of Aluminium Based Metal Matrix Composites

Vinodkumar M. Chandankar, Aarti A. Dyade

Share this Article

Research Paper, Mechanical Engineering, India, Volume 7 Issue 3, March 2018

Pages: 945 - 948

Effect of Zirconium on Mechanical Behavior of Aluminum7075

P. Saritha, Dr. A. Satyadevi, Dr. P. Ravikanth Raju, N. Swapna Sri

Share this Article

Similar Articles with Keyword 'Stir casting'

Research Paper, Mechanical Engineering, India, Volume 4 Issue 5, May 2015

Pages: 1892 - 1895

Investigation of Mechanical Behavior of Ultra Light Weight Nano Composite for Aero-Crafts

S. Gajalakshmi, K. Sriram

Share this Article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 6, June 2017

Pages: 2025 - 2030

Analysis on Mechanical Behaviour of AA 1050/ SiC and AA 1050/Al2O3 Composites

Kapil Singh, Mukesh Kumar

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 8, August 2014

Pages: 1032 - 1036

Weight Optimization of Connecting Rod by Al-Si Metal Matrix Reinforced With Alumina and Flyash

Fayaz Kandagal, Bhimagoud Patil

Share this Article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 11, November 2016

Pages: 1589 - 1594

Fabrication of Aluminum/Magnesium Composite Material and Optimization their Mechanical Properties

Gyanendra Singh, Tanuj Giri

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 8 Issue 12, December 2019

Pages: 1622 - 1629

Some Investigations on Drilling of Aluminium Based Metal Matrix Composites

Vinodkumar M. Chandankar, Aarti A. Dyade

Share this Article

Similar Articles with Keyword 'drilling'

Comparative Studies, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 998 - 1002

Design and Efficiency Comparison of Various Belt Type Oil Skimmers

Mamta Patel

Share this Article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 4, April 2015

Pages: 2987 - 2989

X-Y Cutting Profile Machine

Pournima Wagh

Share this Article

Research Paper, Mechanical Engineering, China, Volume 5 Issue 6, June 2016

Pages: 1053 - 1060

Structural Parameter?s Optimization of LW-800 Type Drilling Fluid Centrifuge

Song Tao Jiu, Guo Jing Gui

Share this Article

Case Studies, Mechanical Engineering, India, Volume 6 Issue 1, January 2017

Pages: 1517 - 1521

Residual Stress Analysis of Mild Steel ASTM A36 in Milling & Drilling

Abin Paul, Akash Paul Savio

Share this Article

Research Paper, Mechanical Engineering, India, Volume 2 Issue 6, June 2013

Pages: 382 - 384

Low-vibration angle grinders

Ramesh Kumar Yadav, Pankaj Kumar Pal, Rohit Choudhary

Share this Article
Top