International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064


Downloads: 141

Review Papers | Mechanical Engineering | India | Volume 8 Issue 3, March 2019


A Review on the Parametric Optimization in MIG Welding using Taguchi Method

Mandeep Singh, Dr. Balbir Singh


Abstract: In the contemporary, MIG welding has wide industrial applications. Parameters utilized in MIG plays a significant role in overall quality, productivity, duration as well as cost of welding. This paper throws light on the influence of welding parameters like welding current, welding voltage, gas flow rate, wire feed rate etc. on the weld strength of Medium Carbon Steel material during welding. By the use of DOE method, the parameters can be optimized to ascertain the best possible combination to achieve desirable quality. Taguchi technique has been used to plan the set of experiments and acquiring the data. An orthogonal array, Signal to Noise Ratio (S/N) and ANOVA is utilized to investigate the welding characteristics of Steel and thereby attaining the welding parameters which gives out desirable result. The confirmation test compares the predicted values with the experimental values to confirm the effectiveness in the analysis of weld strength.


Keywords: MIG welding, Welding parameters, Taguchi technique, ANOVA, Steel


Edition: Volume 8 Issue 3, March 2019,


Pages: 1782 - 1784


How to Cite this Article?

Mandeep Singh, Dr. Balbir Singh, "A Review on the Parametric Optimization in MIG Welding using Taguchi Method", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=ART20196549, Volume 8 Issue 3, March 2019, 1782 - 1784

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'MIG welding'

Downloads: 118

Research Paper, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 1099 - 1103

Parametric Optimization of Metal Inert Gas Welding and Tungsten Inert Gas Welding By Using Analysis of Variance and Grey Relational Analysis

Jay Joshi, Manthan Thakkar, Sahil Vora

Share this Article

Downloads: 119

Research Paper, Mechanical Engineering, India, Volume 3 Issue 5, May 2014

Pages: 523 - 528

Simulation of Robotized Mig Welding Using Robotstudio

Rohit Sharma, Parveen Kalra, Ajay Gupta

Share this Article

Similar Articles with Keyword 'Welding parameters'

Downloads: 117

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this Article

Downloads: 123

Research Paper, Mechanical Engineering, India, Volume 4 Issue 3, March 2015

Pages: 2322 - 2325

Optimisation of Saw Process Parameters for Bead Geometry of Bead on Plate Welds Deposited on Structural Steel IS-2062 Using Taguchi Method

Meenu Sharma, Prof. Dr. M. I. Khan

Share this Article

Similar Articles with Keyword 'Taguchi technique'

Downloads: 104

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1509 - 1515

Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis

D.U.M. Manikanta, A. Chennakesava Reddy

Share this Article

Downloads: 108

Review Papers, Mechanical Engineering, India, Volume 4 Issue 3, March 2015

Pages: 2364 - 2368

Review of Optimization Aspects for Casting Processes

Yazad N. Doctor, Dr. Bhushan T. Patil, Aditya M. Darekar

Share this Article

Similar Articles with Keyword 'ANOVA'

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Downloads: 117

Research Paper, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 2699 - 2702

Optimization of End Milling Parameters on Surface Roughness of Die Steel HCHCr by Taguchi Method

M. S. Harne, Ravikumar L. Shirsat

Share this Article

Similar Articles with Keyword 'Steel'

Downloads: 0

Research Paper, Mechanical Engineering, Turkey, Volume 10 Issue 7, July 2021

Pages: 1327 - 1329

Investigation of the Effect of Normalization Process on Mechanical Properties and Microstructure of the AISI 4140 Alloy Steel

Yusuf YILMAZ, Ethem KESTI

Share this Article

Downloads: 1

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 698 - 702

FEA of Double Shear Lug Joint by Varying Material Combinations

B. Vijaya Kumar, F. Anand Raju

Share this Article

Similar Articles with Keyword 'MIG'

Downloads: 104

Research Paper, Mechanical Engineering, India, Volume 5 Issue 5, May 2016

Pages: 1897 - 1900

Energy Consumption and Optimization in Process Industries

Faraz Ahmad, Dr. R. K. Jain

Share this Article

Downloads: 115

Research Paper, Mechanical Engineering, Ethiopia, Volume 3 Issue 11, November 2014

Pages: 2429 - 2432

Investigation on the Performance of Fuel Stick Fuel Conditioner in Diesel Vehicle

N. Ramesh Babu, Alemayehu Wakjira

Share this Article

Similar Articles with Keyword 'welding'

Downloads: 108

Research Paper, Mechanical Engineering, India, Volume 4 Issue 4, April 2015

Pages: 1396 - 1399

Thermo-Mechanical Analysis in TIG Welding of Aluminium Alloy 6082

Swapnil S. Ingle, Dr. Rajendra S. Dalu

Share this Article

Downloads: 112

Review Papers, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 2002 - 2008

Optimization of Process Parameters for Resistance Spot Welding Process of HR E-34 Using Response Surface Method ? A Review

B. S. Gawai, Dr. C. M. Sedani

Share this Article

Similar Articles with Keyword 'Welding'

Downloads: 108

Research Paper, Mechanical Engineering, India, Volume 4 Issue 4, April 2015

Pages: 1396 - 1399

Thermo-Mechanical Analysis in TIG Welding of Aluminium Alloy 6082

Swapnil S. Ingle, Dr. Rajendra S. Dalu

Share this Article

Downloads: 112

Review Papers, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 2002 - 2008

Optimization of Process Parameters for Resistance Spot Welding Process of HR E-34 Using Response Surface Method ? A Review

B. S. Gawai, Dr. C. M. Sedani

Share this Article

Similar Articles with Keyword 'parameters'

Downloads: 179 | Monthly Hits: ⮙1

Survey Paper, Mechanical Engineering, India, Volume 8 Issue 6, June 2019

Pages: 2320 - 2324

A Review Paper on Electro Chemical Discharge Machining Technique

Rajeev Sharma

Share this Article

Downloads: 227

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 7 Issue 5, May 2018

Pages: 44 - 47

Review Paper on Experimental Investigation on Vortex Tube Refrigeration System

Abhinav Giri

Share this Article

Similar Articles with Keyword 'Taguchi'

Downloads: 104

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1509 - 1515

Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis

D.U.M. Manikanta, A. Chennakesava Reddy

Share this Article

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Similar Articles with Keyword 'technique'

Downloads: 179 | Monthly Hits: ⮙1

Survey Paper, Mechanical Engineering, India, Volume 8 Issue 6, June 2019

Pages: 2320 - 2324

A Review Paper on Electro Chemical Discharge Machining Technique

Rajeev Sharma

Share this Article

Downloads: 63

Review Papers, Mechanical Engineering, India, Volume 10 Issue 3, March 2021

Pages: 225 - 227

Modern Manufacturing Methods: A Review

Balakrishna A M

Share this Article
Top