International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064


Downloads: 117

Research Paper | Mechanical Engineering | Libya | Volume 7 Issue 12, December 2018


Thermal Treatment of Sol-gel Titania Films Deposited on Stainless Steel for Surface Improvement

Blgasam Omer Eissa Al-Sharef, Ahmed.O.Mohamed


Abstract: Four, eight and twelve layers of TiO2 coatings were prepared by the Sol-Gel method. These layers were deposited into SS 316 substrate using dip coating method. The microstructure and surface morphology of titania coatings acquired through sol- gel method were generally assessed using XRD, SEM and optical microscopy, while the composition of titania coating was characterized by EDS. The results revealed that sol-gel deposition succeed in forming titania coating that crystallized in TiO2 (anatase form). The deposited coatings illustrated drastically different composition as well as microstructure in comparison with as- dried coating from the same sol-gel titania group.


Keywords: Sol-Gel, XRD, SEM, SS 316, stainless steel


Edition: Volume 7 Issue 12, December 2018,


Pages: 1529 - 1530


How to Cite this Article?

Blgasam Omer Eissa Al-Sharef, Ahmed.O.Mohamed, "Thermal Treatment of Sol-gel Titania Films Deposited on Stainless Steel for Surface Improvement", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=ART20193911, Volume 7 Issue 12, December 2018, 1529 - 1530

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'XRD'

Downloads: 119

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 9, September 2014

Pages: 426 - 431

Characterization, AC Conductivity and Dielectric behaviour of Chemically Synthesized Poly Meta-Aminophenol

Dr. Shantharaja M., Srinivas K. R.

Share this Article

Downloads: 133

Research Paper, Mechanical Engineering, Ethiopia, Volume 1 Issue 1, December 2012

Pages: 153 - 158

Microstructure Analysis of the Carbon Nano Tubes-Aluminum Composite with different Manufacturing Conditions

Balamurugan Adhithan, Hari Prasada Rao Pydi

Share this Article

Similar Articles with Keyword 'SEM'

Downloads: 2

Review Papers, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 651 - 653

Evaluation of Fatigue Failure of Crankshaft Work on its Bearing and Crank Pin Analytically and Numerically - A Review

Suryakant Rathod, Qaimi Mudassar

Share this Article

Downloads: 106

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 761 - 763

Critical Analysis of Fuel Pump Bleed Valve for Typical Jet Engine by Using FMEA Method

Bharath. G, R. Prakash

Share this Article

Similar Articles with Keyword 'stainless steel'

Downloads: 117

Research Paper, Mechanical Engineering, India, Volume 6 Issue 2, February 2017

Pages: 2132 - 2135

Investigating the Effect of Process Parameters in Manual Metal Arc Welding for Joining Dissimilar Metals

Prajakta G Ahire, U. S. Patil

Share this Article

Downloads: 127

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 7, July 2015

Pages: 1091 - 1095

Multi Objective Optimization of Cutting Parameter in EDM Using Grey Taguchi Method

D. Venkatesh Naik, Dr. D. R. Srinivasan

Share this Article
Top