Comparative Study and Optimization of Dry Sand Abrasive Wear Behavior of As-Cast and Retrogression and Re-Aging of 7075 Aluminum Alloy using Taguchi and ANOVA
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

Research Paper | Mechanical Engineering | India | Volume 7 Issue 4, April 2018

Comparative Study and Optimization of Dry Sand Abrasive Wear Behavior of As-Cast and Retrogression and Re-Aging of 7075 Aluminum Alloy using Taguchi and ANOVA

Jagannath, Hemavathy S

For the past many years 7075 aluminum alloy widely used in aircraft structural parts where high wear resistance are required wear rate are reduced by the retrogression and re- aging heat treatment (RRA). Three body sand abrasive wear test is conducted on both as-cast and retrogression and re-aging specimens as per Taguchis experimental design and L9 orthogonal array wear parameters like time, load, and speed are considered and track diameter kept constant it is found that when wear resistance of retrogression and re-aging heat treated (RRA) specimen is more as compared to the as-cast specimens. The design of experiments (DOE) approach using taguchi method was employed to analyze the abrasive wear behavior of material. Signal-to-noise ratio and analysis of variance (ANOVA) were used to investigate the influence of parameters on the wear rate and also determine the optimal parameters for minimizing the wear rate.

Keywords: AL-7075 alloy, retrogression and re-aging, sand abrasive wear, Taguchis orthogonal array, ANOVA

Edition: Volume 7 Issue 4, April 2018

Pages: 1688 - 1692

Share this Article

How to Cite this Article?

Jagannath, Hemavathy S, "Comparative Study and Optimization of Dry Sand Abrasive Wear Behavior of As-Cast and Retrogression and Re-Aging of 7075 Aluminum Alloy using Taguchi and ANOVA", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=ART20182050, Volume 7 Issue 4, April 2018, 1688 - 1692

91 PDF Views | 92 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'ANOVA'

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this Article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 2699 - 2702

Optimization of End Milling Parameters on Surface Roughness of Die Steel HCHCr by Taguchi Method

M. S. Harne, Ravikumar L. Shirsat

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 1099 - 1103

Parametric Optimization of Metal Inert Gas Welding and Tungsten Inert Gas Welding By Using Analysis of Variance and Grey Relational Analysis

Jay Joshi, Manthan Thakkar, Sahil Vora

Share this Article

Review Papers, Mechanical Engineering, India, Volume 4 Issue 12, December 2015

Pages: 821 - 824

Review on Effect of Powder Mixed Dielectric on Material Removal Rate in Electric Discharge Machining

M. S. Bembde, J. K. Sawale

Share this Article
Top