International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064


Downloads: 120

Research Paper | Production Engineering | India | Volume 6 Issue 11, November 2017


Parametric Optimization of Rotary Electro-Discharge Machining of Oil Hardened Non Shrinkage Steel Material with Sensitivity Analysis

Rahul Shivajirao Desai, M. V. Kavade


Abstract: Optimization tool used in industrial area for increasing quality of product by reducing the cost of product. In this paper, the experimental investigation of material removal rate (MRR), electrode wear rate (EWR) and surface roughness during machining on OHNS Steel by using copper electrode on EDM machine. The input parameters used for experimental work are Peak Current (Ip), Pulse-On (Ton), Pulse-Off (Toff) and Rotation of ram. Based on the input parameters, the design of experiments are L9 orthogonal array. The optimization has been carried out by using Taguchi method as well as Grey relational analysis or Multi response optimization. Firstly single optimization has been carried out and then Multi response optimization has been carried out, for that Grey relational generation and coefficient are find out and then Grey relational grade is carried out. Then the confirmation experiments are carried out. According to this machining parameters are carried out to be optimized for combined objectives of higher MRR, lower EWR and lower SR. The results obtained from this optimization shows that GRA is very effective optimization technique than Taguchi method. Sensitivity analysis also used as a post analysis method


Keywords: EDM, IP, Ton, Toff, MPR, EWR, SR Taguchi method, orthogonal array, GRA, Sensitivity analysis


Edition: Volume 6 Issue 11, November 2017,


Pages: 115 - 123


How to Cite this Article?

Rahul Shivajirao Desai, M. V. Kavade, "Parametric Optimization of Rotary Electro-Discharge Machining of Oil Hardened Non Shrinkage Steel Material with Sensitivity Analysis", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=ART20177815, Volume 6 Issue 11, November 2017, 115 - 123

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'EDM'

Downloads: 95

Research Paper, Production Engineering, India, Volume 6 Issue 3, March 2017

Pages: 2329 - 2335

Effect and Optimization of Process Parameters using Taguchi Method in WEDM for AISI M42 HSS Material

Joshi Guruprasad R., Dr. A. N. Chapgaon

Share this Article

Downloads: 100

Research Paper, Production Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1653 - 1657

Analysis of WEDM Parameters Using Taguchi Method

V. P. Baisane, Y. S. Sable, Hashmi A. Ahmed

Share this Article

Similar Articles with Keyword 'IP'

Downloads: 91

Research Paper, Production Engineering, India, Volume 3 Issue 9, September 2014

Pages: 580 - 583

Economical Methods to Reduce Time Required for Product Quality Inspection in Small Scale Industries

Siddharth Sancheti, Dhanashree Kadulkar, Varun Naik

Share this Article

Downloads: 92

M.Tech / M.E / PhD Thesis, Production Engineering, India, Volume 3 Issue 7, July 2014

Pages: 808 - 812

Comparison of Three Remedial Alternative Solutions' and Selection of Best for Alternative Design of Pressure Board UVSL

Kapil Deshmukh, Dr. S. P. Untawale

Share this Article

Similar Articles with Keyword 'Ton'

Downloads: 95

Research Paper, Production Engineering, India, Volume 6 Issue 3, March 2017

Pages: 2329 - 2335

Effect and Optimization of Process Parameters using Taguchi Method in WEDM for AISI M42 HSS Material

Joshi Guruprasad R., Dr. A. N. Chapgaon

Share this Article

Downloads: 107

Research Paper, Production Engineering, Mexico, Volume 6 Issue 11, November 2017

Pages: 1127 - 1131

Design of a Temperature Control for a Solar Dehydrator

Jose Luis Hernandez Corona, Jose Manuel Lopez Sanchez, Norma Garcia Vazquez, Maria Candelaria Daza Teacalco

Share this Article

Similar Articles with Keyword 'MPR'

Downloads: 91

Research Paper, Production Engineering, India, Volume 3 Issue 9, September 2014

Pages: 580 - 583

Economical Methods to Reduce Time Required for Product Quality Inspection in Small Scale Industries

Siddharth Sancheti, Dhanashree Kadulkar, Varun Naik

Share this Article

Downloads: 95

Research Paper, Production Engineering, India, Volume 6 Issue 3, March 2017

Pages: 2329 - 2335

Effect and Optimization of Process Parameters using Taguchi Method in WEDM for AISI M42 HSS Material

Joshi Guruprasad R., Dr. A. N. Chapgaon

Share this Article

Similar Articles with Keyword 'orthogonal array'

Downloads: 96

Research Paper, Production Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2721 - 2726

Application of Taguchi Method for Resistance Spot Welding of Stainless Steel-304 Grade

Manjunath R. Rawal, Dr. K. H. Inamdar

Share this Article

Downloads: 98

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1331 - 1335

Optimization of Surface Roughness of EN8 Steel by Changing Cutting Parameters and Insert Geometry in Turning Process

K. G. Nikam, S. S. Kadam

Share this Article

Similar Articles with Keyword 'GRA'

Downloads: 91

Research Paper, Production Engineering, India, Volume 5 Issue 8, August 2016

Pages: 1591 - 1598

Formability Limit Diagrams of Cold Deep Drawing Process for Nickel 201 Cylindrical Cups

G. Devendar, A. Chennakesava Reddy

Share this Article

Downloads: 93

Research Paper, Production Engineering, India, Volume 3 Issue 11, November 2014

Pages: 1669 - 1671

Milling Fixture for Arcing Contact

Viraj P. Lele

Share this Article
Top