International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Open Access | Fully Refereed | Peer Reviewed

ISSN: 2319-7064


Downloads: 100

Research Paper | Mechanical Engineering | India | Volume 6 Issue 9, September 2017


Pulsed Laser Micro Polishing of Metals Using Dual-Beam Technology

Lagad Rahul Anil, Dr. Ashwini Kumar


Abstract: In this paper laser micro polishing with an additional laser beam for pre-heating of the surface is examined. Under the influence of the following process parameters on the surface roughness, the present work has been examined Pre-heating laser power, scanning velocity, beam offset of the two laser beams, and intensity distribution of the pre-heating laser beam. Two materials behavior have been used for investigation (martensitic tool steel and TiAl6V4), usually performed by different researchers in last two decades, for martensitic tool steel the micro roughness was increased in comparison to conventional laser polishing with only one laser beam (single-beam technology) due to increasing formation of martensite. For TiAl6V4 the meso roughness of the surfaces was decreased in comparison to conventional laser micro polishing due to longer melt duration, so smoother surfaces were obtained (up to 36 % lower surface roughness for one spatial wavelength regime).


Keywords: Laser micro polishing, Dual-beam technology, Pulse duration, Martensite formation


Edition: Volume 6 Issue 9, September 2017,


Pages: 913 - 916


How to Cite this Article?

Lagad Rahul Anil, Dr. Ashwini Kumar, "Pulsed Laser Micro Polishing of Metals Using Dual-Beam Technology", International Journal of Science and Research (IJSR), https://www.ijsr.net/get_abstract.php?paper_id=ART20176740, Volume 6 Issue 9, September 2017, 913 - 916

How to Share this Article?

Enter Your Email Address


Similar Articles with Keyword 'Laser'

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 4 Issue 4, April 2015

Pages: 1142 - 1145

Genauigkeit Laser Tool for Shafts Alignment

Kanniappan K

Share this Article

Downloads: 108

Research Paper, Mechanical Engineering, India, Volume 4 Issue 10, October 2015

Pages: 1709 - 1711

Design, Manufacture and Test of a Solar Powered Audible Bird Scarer and Study of Sound Ranges Used in it

Vikrant Rajesh Suryawanshi

Share this Article

Similar Articles with Keyword 'micro'

Downloads: 179 | Monthly Hits: ⮙1

Survey Paper, Mechanical Engineering, India, Volume 8 Issue 6, June 2019

Pages: 2320 - 2324

A Review Paper on Electro Chemical Discharge Machining Technique

Rajeev Sharma

Share this Article

Downloads: 0

Research Paper, Mechanical Engineering, Turkey, Volume 10 Issue 7, July 2021

Pages: 1327 - 1329

Investigation of the Effect of Normalization Process on Mechanical Properties and Microstructure of the AISI 4140 Alloy Steel

Yusuf YILMAZ, Ethem KESTI

Share this Article

Similar Articles with Keyword 'technology'

Downloads: 236 | Weekly Hits: ⮙1 | Monthly Hits: ⮙3

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 478 - 481

Design and Development of Solar Powered Air Cooler

Vijaykumar Kalwa, Dr. R. Prakash

Share this Article

Downloads: 2

Research Paper, Mechanical Engineering, India, Volume 10 Issue 7, July 2021

Pages: 425 - 428

RF Controlled Floor Cleaning Machine

Aadil Rehman Singh

Share this Article

Similar Articles with Keyword 'Pulse'

Downloads: 179 | Monthly Hits: ⮙1

Survey Paper, Mechanical Engineering, India, Volume 8 Issue 6, June 2019

Pages: 2320 - 2324

A Review Paper on Electro Chemical Discharge Machining Technique

Rajeev Sharma

Share this Article

Downloads: 49

Research Paper, Mechanical Engineering, India, Volume 10 Issue 1, January 2021

Pages: 1124 - 1127

Effect of Various Parameters on Machining of EN-31 in Wire Electrical Discharge Machining

Rajat, Shiv Kumar

Share this Article

Similar Articles with Keyword 'duration'

Downloads: 236 | Weekly Hits: ⮙1 | Monthly Hits: ⮙3

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 478 - 481

Design and Development of Solar Powered Air Cooler

Vijaykumar Kalwa, Dr. R. Prakash

Share this Article

Downloads: 112

Research Proposals or Synopsis, Mechanical Engineering, India, Volume 6 Issue 11, November 2017

Pages: 1446 - 1449

Test Protocol for Accelerated Creep and Transient Thermo-Mechanical Testing of Super Critical Steam Turbine Rotor

Bishnu Pada Pal, M Naga Suresh, K Ramakrishna, A Narayana Teja, Supak Pore, Prabhat Kr. Hensh, Somnath Nandi, Maneesh Batrani

Share this Article

Similar Articles with Keyword 'formation'

Downloads: 5 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, Turkey, Volume 10 Issue 8, August 2021

Pages: 1099 - 1102

Energy and Stress Analysis of the Free Fall Mechanism Made of Cast Iron with a Mass of 500, 1000, 1500, 2000 Grams and Working at 10, 20, 30, 40 Centimeters Height

Kevser Dincer, Kadir Eren Tekiner, Yusuf Y?lmaz

Share this Article

Downloads: 90

Research Paper, Mechanical Engineering, India, Volume 9 Issue 11, November 2020

Pages: 961 - 964

Nose Design for Formula Student Vehicle with Aerodynamic Components

Harsh Savliya

Share this Article
Top