International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Most Trusted Research Journal Since Year 2012

ISSN: 2319-7064



Research Paper | Mechanical Engineering | India | Volume 6 Issue 2, February 2017

Study of the Effect of Electro-co-deposition on Transmission Gears

B S Praveen Kumar, K M Narayanappa

The word Electro-co-deposition means deposition of Anodic material on to the cathode along with additives which are mixed in to the electrolyte solution. In the present work nickel is used as the anode, Mild Steel Substrate as cathode and Tungsten carbide (WC) is used as additive material.Intially the coating was done on MS plates, later the coating was done on Spur gears. The Coated gears were tested for coating thickness and Hardness. The coated plates were used for characterisation using XRD, as it is not feasible to carry out XRD on the gears after coating. The coating thickness was found to be more uniform throughout the gears but high quality coating was found at the edges. Also Hardness of the coated gears was higher compared to uncoated gears. The XRD Analysis was done for 2 range of 20 to 80 at four degrees per minute. The analysis was used as a confirmation test for Ni-WC crystal growth. With all these increases trends in properties after coating the MS substrate there is wide scope of this technology in Automobile as well as aerospace domains.

Keywords: Electro-co-deposition, Nickel, Tungsten Carbide WC, Mild steel, Coating Thickness, XRD

Edition: Volume 6 Issue 2, February 2017

Pages: 744 - 749


How to Cite this Article?

B S Praveen Kumar, K M Narayanappa, "Study of the Effect of Electro-co-deposition on Transmission Gears", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=ART2017656, Volume 6 Issue 2, February 2017, 744 - 749

29 PDF Views | 36 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'Nickel'

Survey Paper, Mechanical Engineering, India, Volume 5 Issue 2, February 2016

Pages: 2156 - 2162

Optimization of Hydraulic Oil Seal in Earth Movers

R. Vishnu Ramesh Kumar, V. Varun Sagar, P. Vishnuram, N. Hari Prasanth

Share this article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 6, June 2016

Pages: 1103 - 1107

Stress Analysis and Life Estimation of Gas Turbine Blisk for Different Materials of a Jet Engine

Madhu P

Share this article

Research Paper, Mechanical Engineering, India, Volume 7 Issue 6, June 2018

Pages: 1556 - 1562

Cyclic Corrosion and Oxidation of Inconel-600 in Molten Salty Environment at 8000C by D-Gun Sprayed Coating

Sumit Kumar Pandey, Shiv Kumar Tripathi

Share this article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 3, March 2017

Pages: 1551 - 1557

Thermal Load Effect on Bimetal Valve by Using Conventional and Blended Fuels

Guguloth Ravi, Thurai Saishart, Maloth Heeralal

Share this article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1803 - 1807

Assembly Analysis of Piston, Connecting Rod & Crankshaft

L. Karthik Chakravarthy, Dr. P. Srikanth

Share this article



Similar Articles with Keyword 'Mild steel'

Review Papers, Mechanical Engineering, India, Volume 4 Issue 3, March 2015

Pages: 1323 - 1328

Elasto-Plastic Strain Rate Dependent Material Characterization of Steel Grade for Crash Simulation

Shyamkumar Rai, A. K. Dubey

Share this article

Case Studies, Mechanical Engineering, India, Volume 6 Issue 1, January 2017

Pages: 1517 - 1521

Residual Stress Analysis of Mild Steel ASTM A36 in Milling & Drilling

Abin Paul, Akash Paul Savio

Share this article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 1, January 2017

Pages: 1440 - 1444

Ergonomically Design of Multipurpose Portable Wooden Table

D. R. Thawkar

Share this article

Research Paper, Mechanical Engineering, Nigeria, Volume 6 Issue 9, September 2017

Pages: 809 - 816

Experimental Stress Analysis of Some Adhesively Bonded Joints

T.N. Guma, C. Allison

Share this article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 1469 - 1472

Composite Section Design for Minimum Weight in Structural Application

Devendra B. Sonawane, Prof. R. N. Garad, Pratik K. Satav

Share this article



Similar Articles with Keyword 'XRD'

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 9, September 2014

Pages: 426 - 431

Comparison of Riveted Panel and Integral Panel for Damage Tolerance by Using FEA

Dr. Shantharaja M., Srinivas K. R.

Share this article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 2, February 2017

Pages: 744 - 749

Study of the Effect of Electro-co-deposition on Transmission Gears

B S Praveen Kumar, K M Narayanappa

Share this article

Research Paper, Mechanical Engineering, Libya, Volume 7 Issue 12, December 2018

Pages: 1529 - 1530

Thermal Treatment of Sol-gel Titania Films Deposited on Stainless Steel for Surface Improvement

Blgasam Omer Eissa Al-Sharef, Ahmed.O.Mohamed

Share this article

Research Paper, Mechanical Engineering, Ethiopia, Volume 1 Issue 3, December 2012

Pages: 153 - 158

Microstructure Analysis of the Carbon Nano Tubes-Aluminum Composite with different Manufacturing Conditions

Balamurugan Adhithan, Hari Prasada Rao Pydi

Share this article
Top