Comparative Assessment of Carbide Insert and Cermet Insert on Surface Roughness in Boring of ASTM A48 Grey Cast Iron
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064



Downloads: 141

M.Tech / M.E / PhD Thesis | Mechanical Engineering | India | Volume 6 Issue 6, June 2017

Comparative Assessment of Carbide Insert and Cermet Insert on Surface Roughness in Boring of ASTM A48 Grey Cast Iron

Ajay Sankar, Soumyalata.D

Boring is the operation which is extensively used to enlarge and finish the internal holes. The operation requires minimum roughness value. In this experiment, the surface roughness value (Ra) was optimized by varying the spindle speed, depth of cut and feed. The Taguchi design was used to optimize the parameters, MINITAB 17 was the software used for optimization. The work material used for the experiment is ASTM A48 Grey cast iron. Two separate tools are used to bore the internal hole, which are Carbide tool and cermet tool. The Ra value was measured by using the instrument Surftest SJ 410, Mitutoyo. By Taguchi method it was found that Feed rate is the principal factor among the selected process parameters that influences the Ra value in boring operation. Cermet tool gives more surface finish or minimum value of Ra as compared to carbide tool. Thus it is more convenient for performing boring operation for the current material.

Keywords: ASTM A48 grey cast iron, Surface roughness, Boring, Cermet

Edition: Volume 6 Issue 6, June 2017

Pages: 440 - 445

Share this Article

How to Cite this Article?

Ajay Sankar, Soumyalata.D, "Comparative Assessment of Carbide Insert and Cermet Insert on Surface Roughness in Boring of ASTM A48 Grey Cast Iron", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=ART20174143, Volume 6 Issue 6, June 2017, 440 - 445

Enter Your Email Address




Similar Articles with Keyword 'Surface roughness'

Downloads: 100

Research Paper, Mechanical Engineering, India, Volume 6 Issue 9, September 2017

Pages: 913 - 916

Pulsed Laser Micro Polishing of Metals Using Dual-Beam Technology

Lagad Rahul Anil, Dr. Ashwini Kumar

Share this Article

Downloads: 101

Research Paper, Mechanical Engineering, Saudi Arabia, Volume 5 Issue 5, May 2016

Pages: 1447 - 1454

Tactile Perception of Passenger Vehicle Interior Polymer Surfaces: An Investigation using Fingertip Blind Observations and Friction Properties

Mohammad S. Alsoufi

Share this Article

Similar Articles with Keyword 'Boring'

Downloads: 3

Review Papers, Mechanical Engineering, India, Volume 10 Issue 5, May 2021

Pages: 1176 - 1180

Manufacturing Industries in Nepal: Prospects and Challenges

Sanoj Kumar Karki

Share this Article

Downloads: 118 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 6 Issue 5, May 2017

Pages: 1096 - 1100

Motorized Screw Jack

Mohammed Yousuf, Shaik Ashraf, Yaaseen Shahid Iqbal

Share this Article

Similar Articles with Keyword 'ASTM'

Downloads: 116

Research Paper, Mechanical Engineering, India, Volume 3 Issue 7, July 2014

Pages: 2303 - 2309

Influence of Core Density on Flexural Behavior of PUF Cored Sandwich Beams

Mohamed Aqhil Ahmed, Mir Safiulla, Rajesh N

Share this Article

Downloads: 117

Case Studies, Mechanical Engineering, India, Volume 6 Issue 1, January 2017

Pages: 1517 - 1521

Residual Stress Analysis of Mild Steel ASTM A36 in Milling & Drilling

Abin Paul, Akash Paul Savio

Share this Article

Similar Articles with Keyword 'grey'

Downloads: 115

Research Paper, Mechanical Engineering, India, Volume 6 Issue 11, November 2017

Pages: 1833 - 1842

An Experimental Investigation and Optimization of Electrical Discharge Drilling for Small Hole Drilling with High Aspect Ratio

Ashok Kumar, Sandeep Kumar Rawal

Share this Article

Downloads: 118 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 1099 - 1103

Parametric Optimization of Metal Inert Gas Welding and Tungsten Inert Gas Welding By Using Analysis of Variance and Grey Relational Analysis

Jay Joshi, Manthan Thakkar, Sahil Vora

Share this Article

Similar Articles with Keyword 'cast'

Downloads: 3 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2247 - 2249

Vibration Analysis of Two wheeler Connecting Rod

Yeshwant Rao, B S Praveen Kumar

Share this Article

Downloads: 52 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 10 Issue 1, January 2021

Pages: 840 - 847

Experimental Investigation of Aluminium Metal Matrix Composite Reinforced with Aloe Vera Powder

Uppada Sasikala, Dr. Kalapala Prasad

Share this Article

Similar Articles with Keyword 'iron'

Downloads: 0

Research Paper, Mechanical Engineering, India, Volume 10 Issue 6, June 2021

Pages: 1423 - 1428

Improvement in Performance of Heat Exchanger by using Promoters

Saurabh D Vighe, VG Gore

Share this Article

Downloads: 1

Review Papers, Mechanical Engineering, India, Volume 10 Issue 6, June 2021

Pages: 470 - 474

A Theoretical Review of Lubricating or Cooling Systems Used in Machining Processes

Pradeep G

Share this Article

Similar Articles with Keyword 'Surface'

Downloads: 0

Research Paper, Mechanical Engineering, India, Volume 10 Issue 6, June 2021

Pages: 1423 - 1428

Improvement in Performance of Heat Exchanger by using Promoters

Saurabh D Vighe, VG Gore

Share this Article

Downloads: 1

Review Papers, Mechanical Engineering, India, Volume 10 Issue 5, May 2021

Pages: 624 - 626

Air Bearings-Application Review

Sakshi Potdar, Srinidhi Campli

Share this Article

Similar Articles with Keyword 'roughness'

Downloads: 0

Research Paper, Mechanical Engineering, India, Volume 10 Issue 6, June 2021

Pages: 1423 - 1428

Improvement in Performance of Heat Exchanger by using Promoters

Saurabh D Vighe, VG Gore

Share this Article

Downloads: 100

Research Paper, Mechanical Engineering, India, Volume 6 Issue 9, September 2017

Pages: 913 - 916

Pulsed Laser Micro Polishing of Metals Using Dual-Beam Technology

Lagad Rahul Anil, Dr. Ashwini Kumar

Share this Article



Top