Tribological Characterisation and Morphological Study of Epoxy Composites filled with WS2 under Dry Sliding
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064



Downloads: 132 | Monthly Hits: ⮙4

Research Paper | Mechanical Engineering | India | Volume 2 Issue 6, June 2013

Tribological Characterisation and Morphological Study of Epoxy Composites filled with WS2 under Dry Sliding

M. H. Shaikh, G. J. Pawar, J. S. Sidhu

The tribological behaviour of epoxy composites filled with Ws2 particulates were studied using a pin-on-disc wear apparatus under dry sliding conditions. The influence of friction and wear parameters like, percentage of filler content, normal load, sliding velocity and sliding distance on the friction and sliding wear rate were investigated. A plan of experiments, based on the Taguchi technique, was performed to acquire data in a controlled way. The Taguchi design of experiment approach eliminates the need for repeated experiments and thus saves time, material and cost. The results showed that filler content is the most predominant factor as far as the specific wear rate is concerned. The SEM images of the tested samples are also interpreted which shows the anisotropic wear and the wear mechanisms like three body abrasive wear.

Keywords: Composites, Filler, SEM, Taguchi Technique, Tribology

Edition: Volume 2 Issue 6, June 2013

Pages: 462 - 465

Share this Article

How to Cite this Article?

M. H. Shaikh, G. J. Pawar, J. S. Sidhu, "Tribological Characterisation and Morphological Study of Epoxy Composites filled with WS2 under Dry Sliding ", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=0201359, Volume 2 Issue 6, June 2013, 462 - 465

Enter Your Email Address




Similar Articles with Keyword 'Composites'

Downloads: 103

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 11, November 2015

Pages: 2012 - 2018

Design and Analysis of Impact Barriers

Tejaswi Sunkara, U Sudhakar, Dayakar

Share this Article

Downloads: 115

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 7, July 2014

Pages: 759 - 763

Evaluation of Composite Tapered Cone for Torsion using Finite Element Analysis

Zeeshan Khan, Dr. R. J. Patil

Share this Article

Similar Articles with Keyword 'Filler'

Downloads: 120

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 12, December 2015

Pages: 1510 - 1513

A Study on Heat Conductivity Behavior of Zirconia Filled Polyester Composites

Abhinav Mukherjee, Anand Shukla

Share this Article

Downloads: 120

Research Paper, Mechanical Engineering, India, Volume 7 Issue 5, May 2018

Pages: 541 - 544

Parametric Analysis of Reciprocating Friction and Wear Behaviour of PTFE Composite

Pawan I. Patel, Hemant Bhore, Dr. R. R Arakerimath

Share this Article

Similar Articles with Keyword 'SEM'

Downloads: 2

Review Papers, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 651 - 653

Evaluation of Fatigue Failure of Crankshaft Work on its Bearing and Crank Pin Analytically and Numerically - A Review

Suryakant Rathod, Qaimi Mudassar

Share this Article

Downloads: 106

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 761 - 763

Critical Analysis of Fuel Pump Bleed Valve for Typical Jet Engine by Using FMEA Method

Bharath. G, R. Prakash

Share this Article

Similar Articles with Keyword 'Taguchi Technique'

Downloads: 104

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1509 - 1515

Optimization of Fracture Behavior of AA6061 Al-Alloy Pipes Using Finite Element Analysis

D.U.M. Manikanta, A. Chennakesava Reddy

Share this Article

Downloads: 108 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Review Papers, Mechanical Engineering, India, Volume 4 Issue 3, March 2015

Pages: 2364 - 2368

Review of Optimization Aspects for Casting Processes

Yazad N. Doctor, Dr. Bhushan T. Patil, Aditya M. Darekar

Share this Article



Top