Effect of Cutting Parameters on the Surface Roughness of MWCNT Reinforced Epoxy Composite Using CNC End-Milling Process
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

Research Paper | Mechanical Engineering | Malaysia | Volume 2 Issue 11, November 2013

Effect of Cutting Parameters on the Surface Roughness of MWCNT Reinforced Epoxy Composite Using CNC End-Milling Process

G. Harii Krishna Rao, M. N. M Ansari, Shahida Begum

This research reports the study on effect of cutting parameters using CNC Milling to obtain quality surface finish that is specified by customer for machined parts. In this research, an attempt has been made to study the effects of cutting parameter that influence the surface roughness quality. The depth of cut is the most dominant factor of this study. The medium significant factor is feed rate and followed by spindle speed. The most important interactions, that effect surface roughness of machined surfaces, were between the feed rate and depth of cut for this particular type of MWCNT Epoxy composite. This research becomes part of major contribution for the manufacturing industry especially machining of MWCNT/epoxy composite materials using CNC milling process. Interestingly, this project can be regarded as an exclusive work because the information's and solutions achieved at the end of this research was significant and can be implemented in future demanding CNC industries especially in carbon nanotube/epoxy composites applications and alsoas a reference to future researchers.

Keywords: MWCNT, Epoxy Composite, Nanotechnology, CNC milling, Manufacturing

Edition: Volume 2 Issue 11, November 2013

Pages: 51 - 55

Share this Article

How to Cite this Article?

G. Harii Krishna Rao, M. N. M Ansari, Shahida Begum, "Effect of Cutting Parameters on the Surface Roughness of MWCNT Reinforced Epoxy Composite Using CNC End-Milling Process", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=02013372, Volume 2 Issue 11, November 2013, 51 - 55

91 PDF Views | 75 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'Epoxy Composite'

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 12, December 2015

Pages: 1359 - 1361

Development and Thermal Characteristics of Maize-Husk Filled Polymer Composite

Shailesh Verma, Anand Shukla

Share this Article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 4, April 2015

Pages: 1714 - 1717

Glass-Jute Fiber Reinforced Epoxy Composites

Velu.S, Srinivasan.R

Share this Article

Research Paper, Mechanical Engineering, Malaysia, Volume 2 Issue 11, November 2013

Pages: 51 - 55

Effect of Cutting Parameters on the Surface Roughness of MWCNT Reinforced Epoxy Composite Using CNC End-Milling Process

G. Harii Krishna Rao, M. N. M Ansari, Shahida Begum

Share this Article

Research Paper, Mechanical Engineering, India, Volume 2 Issue 6, June 2013

Pages: 462 - 465

Tribological Characterisation and Morphological Study of Epoxy Composites filled with WS2 under Dry Sliding

M. H. Shaikh, G. J. Pawar, J. S. Sidhu

Share this Article

Research Paper, Mechanical Engineering, Malaysia, Volume 2 Issue 12, December 2013

Pages: 273 - 279

Fracture Toughness of Sugar Palm Fiber Reinforced Epoxy Composites

Parween Ali Khudhur, Omer S. Zaroog, Basim A. Khidhir, Zainab Shaker Radif

Share this Article

Similar Articles with Keyword 'Nanotechnology'

Research Paper, Mechanical Engineering, Malaysia, Volume 2 Issue 11, November 2013

Pages: 51 - 55

Effect of Cutting Parameters on the Surface Roughness of MWCNT Reinforced Epoxy Composite Using CNC End-Milling Process

G. Harii Krishna Rao, M. N. M Ansari, Shahida Begum

Share this Article

Research Paper, Mechanical Engineering, Egypt, Volume 6 Issue 10, October 2017

Pages: 559 - 565

Micro Investigation into Positron Annihilation, Tribological and Mechanical Properties of Compacted Zn, ZnO2 and Zn-ZSM-5 Nano Powders

Hala M. Abo-Dief

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 6 Issue 5, May 2017

Pages: 2396 - 2399

Environmental Pollution Control Using Nano-Particles in SI Engines

Rajlaxmi Chaudhary, Dr. Mukesh Thakur

Share this Article

Review Papers, Mechanical Engineering, India, Volume 4 Issue 9, September 2015

Pages: 1451 - 1457

A Review on Nanomaterials?

Radhey M. Bachhav, Suvarna N. Deore

Share this Article

Similar Articles with Keyword 'CNC milling'

Research Paper, Mechanical Engineering, India, Volume 3 Issue 5, May 2014

Pages: 1248 - 1252

Use of Artificial Neural Networks to Investigate the Surface Roughness in CNC Milling Machine

M. Vijay Kumar Reddy

Share this Article

Research Paper, Mechanical Engineering, Nigeria, Volume 4 Issue 7, July 2015

Pages: 2030 - 2036

Cutting Parameters Effects on Surface Roughness During End Milling of Aluminium 6061 Alloy Under Dry Machining Operation

Okokpujie Imhade. P, Okonkwo Ugochukwu.C, Okwudibe Chinenye. D.

Share this Article

Research Paper, Mechanical Engineering, Malaysia, Volume 2 Issue 11, November 2013

Pages: 51 - 55

Effect of Cutting Parameters on the Surface Roughness of MWCNT Reinforced Epoxy Composite Using CNC End-Milling Process

G. Harii Krishna Rao, M. N. M Ansari, Shahida Begum

Share this Article

Research Proposals or Synopsis, Mechanical Engineering, India, Volume 8 Issue 12, December 2019

Pages: 325 - 328

Design and Fabrication of Stool Leg Bush Die for Injection Moulding Machine

V. Venkatrami Reddy, K. Bhaskar Mutyalu

Share this Article

Similar Articles with Keyword 'Manufacturing'

Research Paper, Mechanical Engineering, India, Volume 7 Issue 4, April 2018

Pages: 259 - 261

Self Flowing Generator

Batta Mahesh

Share this Article

Research Paper, Mechanical Engineering, India, Volume 7 Issue 8, August 2018

Pages: 1594 - 1598

Experimental Determination and Investigation into Manufacturing Process to Find Out Causes of Variation (Flatness) and Action Trials to Reduce Variation into Manufacturing Process

Pradeep Kumar, Amit Kumar

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 7, July 2014

Pages: 703 - 706

Computational and Evaluation of Orthogonal Metal Cutting Process Using Ale Method

K. Siddaruda, Gourishankar Hiremath

Share this Article

Review Papers, Mechanical Engineering, India, Volume 4 Issue 2, February 2015

Pages: 1091 - 1093

A Review on Experimental Study of Heat Transfer from Plate Fin in Mixed Convection Mode (Square, Elliptical and Circular Fin)

Rafeek Shaikh, Prof. S. N Doijode, Dr. Mrs. Geeta Lathkar

Share this Article

Research Paper, Mechanical Engineering, China, Volume 5 Issue 1, January 2016

Pages: 1919 - 1923

Research on Simulation Algorithm of Spiral Bevel Gear?s Virtual Manufacturing

Senait Asefa Mesesha, Zhao Wei, Wang Kuan

Share this Article
Top