An Experimental Investigation of the Effect of Carbon Content on the Wear Behavior of Plain Carbon Steel
International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
www.ijsr.net | Open Access | Fully Refereed | Peer Reviewed International Journal

ISSN: 2319-7064

Research Paper | Mechanical Engineering | India | Volume 2 Issue 7, July 2013

An Experimental Investigation of the Effect of Carbon Content on the Wear Behavior of Plain Carbon Steel

Amit K Gupta, Deep Narayan Mishra

Wear behaviour of various carbon steels used in different industries has a direct impact on the performance of mechanical systems. In the present investigation the wear behaviour of carbon steels having varying carbon percentage has been studied, utilizing a pin-on disc sliding tribometer. Experiments were carried out under dry condition. Normal load applied was 5 25 N at a fixed rotational speed of 480 rpm. Results indicate that the wear performance of steel significantly governed by the chemical composition of material. Results have also shown that wear of carbon steel is markedly reduced by adding more carbon to it. Results obtained from experimental procedure shown by different graphs.

Keywords: carbon steel, friction, wear, pins on disc

Edition: Volume 2 Issue 7, July 2013

Pages: 222 - 224

Share this Article

How to Cite this Article?

Amit K Gupta, Deep Narayan Mishra, "An Experimental Investigation of the Effect of Carbon Content on the Wear Behavior of Plain Carbon Steel", International Journal of Science and Research (IJSR), https://www.ijsr.net/search_index_results_paperid.php?id=02013119, Volume 2 Issue 7, July 2013, 222 - 224

77 PDF Views | 71 PDF Downloads

Download Article PDF



Similar Articles with Keyword 'carbon steel'

Research Paper, Mechanical Engineering, Iraq, Volume 3 Issue 12, December 2014

Pages: 2425 - 2431

Effect of the Rolling Direction and Draft on Some of the Mechanical Properties for the Medium Carbon Steel

Younis Fakher Aoda, Dr. Lattif Shekher Jabur

Share this Article

Research Paper, Mechanical Engineering, Iraq, Volume 5 Issue 7, July 2016

Pages: 1406 - 1410

A Study on Ammonia Condensation in Bundles of Low-Fin Carbon Steel Tubes

Eaman Hassan Al-Saoub

Share this Article

Research Paper, Mechanical Engineering, India, Volume 6 Issue 2, February 2017

Pages: 2132 - 2135

Investigating the Effect of Process Parameters in Manual Metal Arc Welding for Joining Dissimilar Metals

Prajakta G Ahire, U. S. Patil

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 5, May 2014

Pages: 507 - 511

Effect of Process Parameters on Surface Roughness and Surface Hardness in Roller Burnishing Process

Jignesh R. Patel, Prof. S. M. Patel

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 3 Issue 12, December 2014

Pages: 2563 - 2567

Study Effect of HSS Single Point Cutting Tool Nose Radius on Cutting Edge Strength and Tool Wear in Machining of EN9

Maheshwari Patil, Dr. R. J. Patil

Share this Article

Similar Articles with Keyword 'friction'

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 5 Issue 5, May 2016

Pages: 1150 - 1152

Friction Control in Planetary Gearbox by Selecting Grease with Proper Viscosity

Vivek V. Salve, R. M. Tayade

Share this Article

Research Paper, Mechanical Engineering, Saudi Arabia, Volume 5 Issue 5, May 2016

Pages: 1447 - 1454

Tactile Perception of Passenger Vehicle Interior Polymer Surfaces: An Investigation using Fingertip Blind Observations and Friction Properties

Mohammad S. Alsoufi

Share this Article

Research Paper, Mechanical Engineering, Indonesia, Volume 8 Issue 9, September 2019

Pages: 1457 - 1459

Optimization Analysis of Turning Process Parameters for Shaft Characteristics

F Rahmadianto, Totok Soegiarto, Soeparno Djiwo

Share this Article

Research Paper, Mechanical Engineering, India, Volume 4 Issue 5, May 2015

Pages: 2857 - 2861

Analysis of Heat Transfer in Turbulent Channel Using Grooves

Mayank Bhola, Dr. Satyendra Singh

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 2770 - 2774

Numerical Analysis of Heat Transfer Characteristics of Finned Tube Heat Exchanger Using System CFD (Flownex)

Prasanna Shankara R, Harikanth S

Share this Article

Similar Articles with Keyword 'wear'

Research Paper, Mechanical Engineering, India, Volume 4 Issue 6, June 2015

Pages: 1808 - 1813

Modeling & Analysis of Labyrinth Seals Used in Steam Turbines

L. Karthik Chakravarthy, Dr. P. Srikanth

Share this Article

Research Paper, Mechanical Engineering, India, Volume 5 Issue 5, May 2016

Pages: 1819 - 1822

Comparative Analysis of Wear for Excavator Bucket Tooth Using Different Materials

Dr. Sabah Khan, Sheikh Mohashin

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 4 Issue 10, October 2015

Pages: 2148 - 2152

Fault Diagnosis Method for Mechanical Rotor Systems using ANN

Deepak Nath V P, A K Saha

Share this Article

Research Paper, Mechanical Engineering, India, Volume 3 Issue 6, June 2014

Pages: 2400 - 2402

A Review Paper on Hardfacing Processes; Materials; Objectives and Applications

Digambar B, Dr. D Choudhary

Share this Article
Top